Jump to content
SAU Community

Recommended Posts

As mentioned, R34 25GT 2001 Auto.

Thinking about replacing/might have to replace my rear diff due to old damage rearing its head slowly (ongoing repairs as things show themselves), it's an auto and I just wanna know what options I have other than buying a second hand one.

Thanks, Teir.

Link to comment
https://www.sau.com.au/forums/topic/390070-r34-25gt-2001-rear-diff-choices/
Share on other sites

Grease leaking from the CV joint, really no way to tell till I get it checked out more, it was a side impact into a small gutter, but hard enough that I span 360 and over the gutter. Baring, ctrl arms, rack and pinnion all changed. while I'm not sure if I'll end up having to replace the diff or not, just wanting to know my options.

The CV could have been damaged, but I'd bet that if it was, you'd really notice it driving around. It's more likely that the boot on the CV is just split (either from normal aging or perhaps from being stressed during the gutter crash).

The reason I wouldn't expect the diff to have suffered too much is that there is a sliding connection between the hub and the outer end of the driveshaft, so there's already one place where movement can occur without transmitting load along the shaft, then you have CV joints at each end of the shaft, so thay can absorb an amount of movement (and perhaps damage) before transmitting a lot of force along the shaft - all before the connection at the diff's axle flange. In order to damage the diff, you'd have to overcome all those little buffers, and to do that you'd be simultaneously making big damage to the various suspension arms. It is far more common in such impacts to do small but noticeable damage to the suspension arms, and to bend the rear subframe, than to damage the diff.

if you wish to replace the diff, just get a turbo R34 diff centre and use the Auto Crown on it to maintain the right ratio. From memory, R34s and S15s both use Torsen diffs, which IMO is great for street and light track work as they don't "thump" and don't require as much maintenance as your conventional clutch pack mechanical diffs

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...