Jump to content
SAU Community

Recommended Posts

Okay about six months ago before I used the wrong fuel and detonated my engine I was making 223rwkws (the engine had just been rebuilt, don’t just 8000ks). Since then the engine has been repaired again replacing two pistons and all the rings. After running it in I changed the oil and headed down to Race Pace with Mobil 8000 in the car. After Ben made the necessary adjustments the car put out just 203rwkws. Ben played around for quite some time and couldn’t get the car to match its previous 223rwkw run. The 20rwkw loss is unexplainable since nothing in the car has really changed.

The performance loss is not really the issue though. For some reason the engine was pinging on the dyno, Ben fixed this but whenever I boot it now the “Check” light goes off flashing. Basically the car is still ever so slightly pinging :mad: Any ideas on why the car might be making less power and why a well turned engine with good fuel oil and so on would be pinging?

Link to comment
https://www.sau.com.au/forums/topic/39240-powerloss-pinging/
Share on other sites

well, there are alot of different things that can cause detonation and powerloss.

BOV leaking or leak in one of the intercooler pipes and vacuum lines is the first place I would be looking.

Then you could check the injectors are flowing ok, if you have an adjustable fuel pressure reg, is the pressure the right - its easy for someone to accidentally fark with shit when its sitting on a work bench.

A couple of places that may be worth looking at anyways - alot of stuff can happen to an engine when it is pulled apart.

Link to comment
https://www.sau.com.au/forums/topic/39240-powerloss-pinging/#findComment-797378
Share on other sites

Thanx for the time guys, took it to Ben today and he fixed it ... think it was mostly a dodgy knock sensor. Anyway, the car runs better and safer now. Cant really tell you what he did, just used some of that magic of his!

Link to comment
https://www.sau.com.au/forums/topic/39240-powerloss-pinging/#findComment-798350
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...