Jump to content
SAU Community

Exhaust Shops In Sydney (Parra/livo Area)

dori34

By dori34,
in New South Wales

 Share

Recommended Posts

dori34 Grand Master

dori34

Posted
Posted

hi gang,

need an urgent job done (plumbing up my gate) tomorrow.

is there any recommended exhaust shops in parramatta/liverpool area that will be open till 5pm to do this?

so i can drop my car off at 9am and i wont be able to pick up until after 4pm.

cheers for the help guys.

StageIan Rising Star

StageIan

Posted
Posted

I think thats where I'll be going for my zorst. I got similar prices from a few shops but Hak was the only one with experience with a Stag. He also said that when they make them they do it so you can bolt up any original part if needed.

I'll be going there as soon as I'm fit enough to drive & work has paid me out.

dori34 Grand Master

dori34

Posted
  • Author
Posted

does Hak open on Saturdays? i've heard a few good things about Hak as well.

i went to Liverpool exhausts after being quoted $150 on the phone after explaining to them exactly what i wanted - they said yeap no worries, bring it in on sat morning and we'll sort you out.

i went there and the price magically jumped up to $380 for no reason.

i said no thanks, and left.

Aggroman Grand Master

Aggroman

Posted
Posted

Yeah Haks will do saturdays but best to have an appointment.

Tell him dave from unigroup sent you and you might get a bit of a discount, may have to call him a dog rooter though :P

its technically northmead not North parra..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...