Jump to content
SAU Community

Recommended Posts

As topic say i have a Nismo Clutch Disk only with box and everything even the nismo certificate. Anyway as i rushing for $$$ so therefore i need to let this go..

The product number is 30100-RN255. I bought it for $480 and now i am open for any reasonable offer as it is NEW haven been use at all. IT is a

Clutch Disc [Non Asbest]

Pull Type for sigle plate. Pressure=1050Kgf

std clucth is only 900Kgf

According to manual this clutch suit

G610 & G810 (L20)

CA18ET & RT18DET

HR31 GTS-R

S12 S13 RS13 (CA18ET, CA18DE, CA18DET)

PS13 (SR20DE)

BNR32 (RB26DETT) BCNR33 (RB26DETT)

R34 GTT (RB25DET) R33 GTST Not sure need to check

S30 (L20), HS30(L24)

KRZ31(VG30DE), WD21(VG30DE)

CZ32(VG30DETT)

Please let me know if any of interested by email at [email protected] or 0418 388 125

Also i have a Trust oil cooler which i am still considering if any of you interested pls let me know too. I am after 700 for the cooler itself

Calvin

Link to comment
https://www.sau.com.au/forums/topic/39360-nismo-clutch-disk-trust-oil-cooler/
Share on other sites

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...