Jump to content
SAU Community

Recommended Posts

I have set of height and damper adjustable coilovers to suit r33/34gtr, in very good condition and not as harsh as many but still give very good handling $900, will post pics soon

these can also fit r34 gtt, the rears are perfect and the fronts with my supplied spacer plate will fit fine but are very low and scrape slightly on hard lock, but if you like it low and are carefull they will be ok

will ship at buyers expence, email [email protected] for direct pics

also have a set of brand new r34 gtt shocks with springs $150neg

r34 gtr front shocks and springs $150neg

rb25 plenum lower half runners $50

rb25 crossover pipe with BOV $50

std cam gear rb $20

rb25 throttle body no tps,$40

rb20 throttle body no tps $40

have other stuff will post soon

Want to swap the coil overs with lowell or whatever my lowered springs are (australian made according to my friend) plus cash? It's off r34 gt-t

no sorry dont have the 34 anymore so dont need any shocks

the ride is firm and handles very well, not as harsh as some cars with tein coilovers i have ridden in but thats just my opinion, very hard make deffinate comment with so may variables

  • 2 weeks later...

Hi Clint,

When you say they are low (front) is that with or without your spacer? I think they are actually R Tune as the S Tune are not height adjustable according to the Nismo site.

Then again I could be wrong, either way, a great set of undercarriage

Cheers

Muz

Hi Clint,

I would love the rears but the fronts are going to be tooooooo low for mine. Nismo site says R Tune = 9 on the front and 8 on the rear, S Tune = 6.8 on front and 4.6 on the rear.

Cheers and good luck with the sale Clint

Muz

  • 2 weeks later...

So they are still TOO low on the highest setting - at the front end?

I thought being adjustable [height] you would be able to set them at a nice comfortable level :confused:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...