Jump to content
SAU Community

Recommended Posts

I have set of height and damper adjustable coilovers to suit r33/34gtr, in very good condition and not as harsh as many but still give very good handling $900, will post pics soon

these can also fit r34 gtt, the rears are perfect and the fronts with my supplied spacer plate will fit fine but are very low and scrape slightly on hard lock, but if you like it low and are carefull they will be ok

will ship at buyers expence, email [email protected] for direct pics

also have a set of brand new r34 gtt shocks with springs $150neg

r34 gtr front shocks and springs $150neg

rb25 plenum lower half runners $50

rb25 crossover pipe with BOV $50

std cam gear rb $20

rb25 throttle body no tps,$40

rb20 throttle body no tps $40

have other stuff will post soon

Want to swap the coil overs with lowell or whatever my lowered springs are (australian made according to my friend) plus cash? It's off r34 gt-t

no sorry dont have the 34 anymore so dont need any shocks

the ride is firm and handles very well, not as harsh as some cars with tein coilovers i have ridden in but thats just my opinion, very hard make deffinate comment with so may variables

  • 2 weeks later...

Hi Clint,

When you say they are low (front) is that with or without your spacer? I think they are actually R Tune as the S Tune are not height adjustable according to the Nismo site.

Then again I could be wrong, either way, a great set of undercarriage

Cheers

Muz

Hi Clint,

I would love the rears but the fronts are going to be tooooooo low for mine. Nismo site says R Tune = 9 on the front and 8 on the rear, S Tune = 6.8 on front and 4.6 on the rear.

Cheers and good luck with the sale Clint

Muz

  • 2 weeks later...

So they are still TOO low on the highest setting - at the front end?

I thought being adjustable [height] you would be able to set them at a nice comfortable level :confused:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...