Jump to content
SAU Community

Rust Inside Diff - Advice Needed!

samos69
 Share

Recommended Posts

samos69 Enthusiast

samos69

Posted
Posted

Hi All,

A while back I bought a 2 way nismo LSD for my R32. It's sat in my garage with the backing plate on and wrapped in shipping plastic on a pallet. Unfortunately my garage is very damp and any bare metal does rust rather quickly. I finally got around to pulling the backing plate and found there is some rust on the diff rant.gif

As far as I can tell it's only on a couple of bolts on the crownwheel (?) and the two caps that hold the diff in the housing, all the important bits had a coating of oil and seem fine. My question is do I pull these parts out and give them a wirebrush then reinstall? Or do I need to pull apart an old open diff I have that is full of oil and will have no-rusted parts (are the caps interchangable?) Do I ignore it and just fill it up with oil then go racing?

Here's a pic, the rust is very crumbly and would come off easily.

IMAG0186.jpg

Also, how clean do I need to get the backing plate of old gasket goo? Completely clean, or just all major lumps taken off? And how much do I use to seal it?

IMAG0187.jpg

Any advice is much appreciated, I'm no expert on these matters!

Cheers

Sam

Link to comment
https://www.sau.com.au/forums/topic/396929-rust-inside-diff-advice-needed/
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

Step 1: Buy 2L of LSX-90

Step 2: Drive around for 100km or until the oil is at least hot

Step 3: Drain oil, wipe drain plug with magnet and fill it up with your favourite blend

Diff's are extremely forgiving, if it was a conrod bolt with rust I would be saying pull it apart.

turboedsloth Grand Master

turboedsloth

Posted
Posted

If you wanted to get really anal you could remove the caps one at a time and bead blast them. You can't interchange caps from other diffs as they are matched to the diff housing like a girdle is in an engine.

As for the glue, scrap as much off as you can and give both surfaces a rub with an oil stone which will make it nice an clean,

samos69 Enthusiast

samos69

Posted
  • Author
Posted

After a scuff up there didn't seem to be any debris that could come loose so I just went ahead and sealed it up. The backing plate has a metal gasket on it which I've never seen before... just put some high temp RTV over it and torqued it up. Will fill it with oil in the morning and see if it leaks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Blue slip

      By MBS206 · Posted

      Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
    • PranK
      Blue slip

      By PranK · Posted

×
×
  • Create New...