Jump to content
SAU Community

Recommended Posts

Hey guys have a Tilton pedal setup brand new never used comes with everything needed besides lines.. Cylinder sizes are 2x3/4 and 1x7/8.. Only thing is the remote reservoir mounts have been chopped for a different mounting position...

Please note this is not a bolt in job.. will require some fabrication skills at the bare minimum

Price is $1900 - located in mackay qld but will post anywhere

538898_286791308067118_100002087526537_672697_534464803_n.jpg

Edited by spenda
Link to comment
https://www.sau.com.au/forums/topic/397629-tilton-pedal-assembly/
Share on other sites

It was bought overseas but i got smashed with nearly 600$ of import taxes.. There is no throttle cable with it but yes the linkage is included.. You can see it in the photo on the left hand side of the accelerator pedal bolted on.

  • 2 weeks later...
  • 2 weeks later...

Will trade for things like bnr33 gtr standard front bar or some aftermarket gtr bars and lip, sideskirts, gtx3582r, big wastegates looking for two 60mms, titanium r33gtr catbacks and thats about it other than those items i would like money..

Not intending to be rude or anything but the reason it probably hasn't sold is that it's actually an old model 600 series pedal set.

I have one at the workshop that I bought into stock from earls for $650 when the 2011 600 series was released.

Masters are $124 per kit each.

That's just a touch over 1k of new with warranty value.

i see said the blind man... oh well thanks for letting me know.. on another note though that throttle linkage is 100+ on its own, the 90degree adaptor for the bias adjuster is around 80 and the bias adjuster is another 70ish..

but that doesnt add up to much anyways.. you are right though that is for a new set.. mine is all unpacked, missing tiny bits and pieces and has no warranty so therefore i will adjust my price accordingly..

buy it all now for $850 + post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...