Jump to content
SAU Community

Boostworx/Ben's 10sec JZA70 Supra... written-off :(

whatsisname

By whatsisname,
in South Australia

 Share

Recommended Posts

whatsisname Grand Master

whatsisname

Posted
Posted

Ben's 'Boostworx' sponsored 10sec Supra came to a sad end late today :) Thankfully Ben is ok!!!

This is all second hand info, so don't take it ALL as gospel...

A Dawoo of some description did an illegal U-turn causing Ben to take evasive action to avoid hitting it! The Supra clipped the gutter in the process and this caused it to spin. Ben hit a stobie pole just forward of the front door area. Shaun said had it hit at the door... Ben would've been in BIG trouble :D

As the other car wasn't actually involved in the crash they left the scene, giving the finger and swearing! If anyone has any info that leads to the ID'ing of said Dawoo then pls let me know.

Most of the drivetrain is suppose to be still ok and will hopefully make it back into a new chassis?

The new engine hadn't even been fully run-in yet :D Early trial tuning saw 360rwkw on 16psi at 5500rpm. They intend to use closer to 7000+/-rpm and 20+psi. I'm guessing high 400's to 500rwkw will be on the cards, as the turbo wasn't even into the start of it efficency range.

COPYME Collaborator

COPYME

Posted
Posted
Ben's 'Boostworx' sponsored 10sec Supra came to a sad end late today :) Thankfully Ben is ok!!!  

This is all second hand info, so don't take it ALL as gospel...

A Dawoo of some description did an illegal U-turn causing Ben to take evasive action to avoid hitting it! The Supra clipped the gutter in the process and this caused it to spin. Ben hit a stobie pole just forward of the front door area. Shaun said had it hit at the door... Ben would've been in BIG trouble :D    

As the other car wasn't actually involved in the crash they left the scene, giving the finger and swearing! If anyone has any info that leads to the ID'ing of said Dawoo then pls let me know.  

Most of the drivetrain is suppose to be still ok and will hopefully make it back into a new chassis?  

The new engine hadn't even been fully run-in yet :D  Early trial tuning saw 360rwkw on 16psi at 5500rpm. They intend to use closer to 7000+/-rpm and 20+psi. I'm guessing high 400's to 500rwkw will be on the cards, as the turbo wasn't even into the start of it efficency range.

So where did this happen? Post a pic?! This isnt going to be like R34 GTR crashed in adelaide is it?

whatsisname Grand Master

whatsisname

Posted
  • Author
Posted

Not sure on the location?

I VERY much doubt it will be like the "GT-R crashed" thread, as Ben's Supra is very well known. Not much chance of mistaking it. It has been a ZOOM cover car and was a regular AIR competitor. It also made over 420rwkw at Autosalon one year.

The new motor has BIG potential! Hopefully it'll find a new home sooner rather than later.

Revhead Grand Master

Revhead

Posted
Posted

I can't believe the farkwits in the Daewoo didn't at least check that he was OK... :) I hope the pricks get caught. I hate it when someone in a nice car is automatically blamed (he will be) for an accident caused by an idiot like this. Sort of makes you wish that he'd run up the arse of the Daewoo - the friggen retard in the buzzbox would get their just desserts, and Ben might have actually gotten some form of compensation...

Rob Collaborator

Rob

Posted
Posted

OMG that is on ***in bad!, I can not believe the other car did a runner.... I hate fugging Daewoo's!!!!!!!

Hopefully he will get it all put into an other chassis, and get it back on the road.

If only my Supra (same shape) was as fast as his.... such a beast of a car.

Did I mention I hate Daewoo's!

COPYME Collaborator

COPYME

Posted
Posted
OMG that is on ***in bad!, I can not believe the other car did a runner.... I hate fugging Daewoo's!!!!!!!

Hopefully he will get it all put into an other chassis, and get it back on the road.

If only my Supra (same shape) was as fast as his.... such a beast of a car.

Did I mention I hate Daewoo's!

Daewoos are Korean Crap! :throwup: Still a very good thing that no-one got hurt! Very frustrating all the same though

whatsisname Grand Master

whatsisname

Posted
  • Author
Posted

Revhead (Marc) you hit the nail on the head mate! Ben will undoubtedly have the finger of blame pointed at HIM, for no other reason than the type of car he drives, or drove... in this case :)

The cost of repairing, or replacing, the s/pole and downed power lines will add up to quite a bit ;)

It could've been a LOT worse I guess? Ben is ok and the new engine combo should be fine. Looking at that photo it shows the rear end is still fine too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      NC MX5

      By Duncan · Posted

      There was a great one on Victoria Rd in Gladesville too back in the day. I can only assume GTSBoy is thinking of the mill up on the wollondilly, no restaurant there any more but they have restored the original steam engine on site and run it every few months, have an annual steampunk festival etc @The Bogan, you came to the wrong town for restaurants. we have a few reasonable asian and indian options but the Paragon is as good as it gets otherwise. That brewery is apparently just opened, been meaning to give it a go some time. The Highlands have plenty of fancy options but I suspect you are more a hearty eater than fancy eater
    • Duncan
      Squeaking clutch/throw out bearing

      By Duncan · Posted

      Thanks for coming back to post the update, maybe it will help out the next person!
    • WMDC35
      Engine model

      By WMDC35 · Posted

      Going by the intake & injectors I'd be guessing it's a DE, check the head casting number, should be 5L8 on a DET, 5L7 I think is the DE number.
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      For future reference, if you need to use Deutsch connectors but don't have the proper crimper for the round style pins, you can get regular style crimp pins too
    • GTSBoy
      Engine model

      By GTSBoy · Posted

      No. The castings are all the same. As you have the inlet off, simply measure the diameter of the inlet ports and compare with the freely available on the net sizes of turbo and NA. The NA ones are small.  
×
×
  • Create New...