Jump to content
SAU Community

Recommended Posts

hey guys

tonight whilst driving my 32 i noticed that once it comes on boost it starts hesitating/ misfiring abit and a cloud of black smoke out the back. I put $20 of BP 98 in it before hand and thats when i started noticing it and thats the first time it happened, the night before i went on the Antilag cruise and again put fuel in before hand and it had no problems came on power fine and smooth.

the car has splitfire coil packs with standard BOSCH plugs, forward facing plenum with saard injectors and a 35R turbo with 44mm gate

im thinking it could be a bad batch of fuel?? possible coil pack?? and maybe the standard plugs have given up on life and thats causing the drama

it idles fine, drives fine with no misfire but as soon as it creeps up to about 4-4.5rpm as the power comes on thats when it starts to hesitate and misfire, sometimes its not bad then some other times its pretty bad any suggestions????

cheers

Link to comment
https://www.sau.com.au/forums/topic/398852-32-misfiring-hesitating/
Share on other sites

Sounds like plugs or coils. When there is a lot of fuel/air going in it blows out the spark. Either gap is too large on the plugs or coils aren't making strong enough spark or spark is going somewhere else instead of to the plugs. If the gap is too large I.e. works ok with smaller gap plugs, then its likely the coils are getting old. Smaller gap is just a temp fix for the inevitable.

well i was gonna put new platinum plugs in and take it for a spin if no real change is there was gonna swap splitfires with my mrs's 32 and see if that makes a change then i can cross a few possible causes off my list

well i had a set of platinums sitting around so i put them in and drove it the hesitation is gone but still has abit of a misfire i looked inside each coil pack when i changed plugs and cylinder 1 coil had a white powdery resedue and the little coil spring inside is like gone and all other coils are clean and have no pwdery stuff in it, and the top of the old plug was powdery and all crapped up, so i have a feeling its a combination of shit plugs which are failing when hot? and a crapped out cylinder one coil pack?

ok so i swapped a whole coil pack assembly for all 6 cylinders and the harness from my mrs's car to mine and took it for a spin, still the same result, like a popping, misfiring sound, doesnt really seem to miss i think i can rule out its a coilpack if mine runs the same with 2 different harnesses, i even swapped the dud looking one with the white shit in it to her car and took hers for a drive and hers ran nicely no miss or hesitation, im going down the lines that the pooping/ miss sound is maybe from the screamer pipe under abit of heavy acceleration??, it doesnt do it all the time when on boost just sometimes through the rev range, might even pay to get plugs with a .8mm gap??

cant swap ignitor pack, i have a series 2 rb25 and the ignitor packs are built into the coil packs and ive swapped all of them and i still got the same result, maybe i need to get plugs with the right gap, whats weird is it ran fine before for ages then it started to play up, i swapped plugs with new platinums, it got alot better but not perfect

  • 2 weeks later...
  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...