Jump to content
SAU Community

Recommended Posts

Hello all,

I am hoping to get some much needed advice in regards to my front suspention. I drive a '96 R33 GTST and over the past couple of months/weeks I have noticed a 'sag' in the front drivers side wheel guard. I believe it is a good 20mm difference between my front right side and my front left side height. This has become even more noticeable lately due to the rubbing of my tyre on the inner plastic wheel guard when I have close to full lock or go over speed bumps.

Anyway, I took the car to my mechanic today to see what is going on. Apparently my bump stop on the right had side is failing to repond to raising attempts. I have been told that my left hand side is more rigid, and the right is soft, so the car will tend to rock to the right side (causing rubbing in some circumstances). I currently have Nismo shocks in the fronts.

So, I have asked what my options are. I have been told that at the moment this isn't a major issue, and the rubbing is minimal, with no chance of and major damage being caused. I had the notion of getting new Bilstein shocks (which would match my rear Bilsteins) to see if that would help, but apparently it will have no effect as its the bump stop and springs that are keeping the car at that height.

I have been advised to look at a coilover set. Tein Super Street coilovers or HSD's have been suggested. The only thing that is stopping me about going this route is a) the price, and b) do I really need this setup?

Your suggestions and thoughts would be greatly appreciated.

Thanks

Edited by The White Knight

A shock absorber doesnt hold the car up, the spring does...

replace springs, but while your at it you may as well replace front two shocks with some more bilsteins to match the rear, replace springs, boots and bumpstops.

That as cheap and reliable as you can get out of this one...

then wait for something else to break.

Agreed. Do not buy coilovers (just for the front) as they will not match whatever you have in the rear real well, and it could be awful.

By the way, I don't know what drugs your mechanic is on, as there is no adjustment of any sort in the factory front strut on a Skyline.

I think he has worded it wrong. I am not entirely clued up on suspension components, but from what I have gathered, he things the RHF strut is done, and the bump stop on that side can't be adjusted.

I asked about throwing Bilstein shocks, new springs, boots and bumpstops in, but he seemed to think that wouldn't be the best option.

I should mention that I completely trust this guy with my car, he has never led me down the wrong path, and he even suggested to find whatever I need (be it coilovers, or whatever) on the net or find the cheapest I can, then he will put them in. So with that, he isn't trying to push any particular brands or components.

Agreed. Do not buy coilovers (just for the front) as they will not match whatever you have in the rear real well, and it could be awful.

By the way, I don't know what drugs your mechanic is on, as there is no adjustment of any sort in the factory front strut on a Skyline.

GTSBoy, I would go coilovers as a set, so I'd take out the rear Bilsteins.

I may look at what 75coupe has suggested, as that seems the most logical seeing as I already have a good rear setup

I dont trust him already...

Bumpstops not adjustable, just saying that is bizarre....

So your going to replace two apparantly ok rear suspension struts because he said its best..?

crazy and will cost you $1200 just for parts, btw you could do the install yourself its easy as, like easy, like changing a tyre easy...

two bilsteins struts, $400 if look around brand new... and done...

Thanks 75coupe, you have been helpful.

I have been looking up posts on Bilstein and Whiteline setups. This looks promising, seeing as I pretty much have half of it done already. My only other concern would be buying bumpstops.

I shall look into it.

Thanks again

Bump stops could be removed from the car completely and you would not know the difference unless you tried to Dukes of Hazard the car. They have absolutely nothing to do with ride height or body control, except at the extreme of suspension travel (like if you hit a brick, spoon drain, or jump a bridge yeeeeehaaaaaw!)

Edited by GTSBoy

use the stock bumpstops they are fine as long as they are still in ok condition..

If your useing lowered springs cut the bumpstop down a tad, this is what I did, there is no problem...

make sure you use boots though, they are the rubber sleeve that covers the strut, the shiny rod of the shock absorber, you dont want dirt getting in there it will shorten the life of the shock by chewing the seal out..

I used generic CV boots from repco, $12ea easy to get... or I also though I could use a bicycle tube cut down, I used some wire straps to make sure the boots stay in place protecting the strut...

It really is an easy job replace suspension, do it yourself save a heap, feel good afterwards...

get an aligement afterwards to be sure its all sweet... it your lowering def get an alignment and give thought to camber adjustment parts, there's a whole heap more info on that subject to be learnt... search

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...