Jump to content
SAU Community

R33 Fog Lights Stopped Working Last Night

KrazyKong

By KrazyKong,
in General Maintenance

 Share

Recommended Posts

KrazyKong Proficient

KrazyKong

Posted
Posted (edited)

My fog lights stopped working last night. I checked the 15amp fuse under the dash today and its fine. What I do hear is this clicking sound similar to when the AC clicks on and off. It's coming from the fuses in the engine bay. Do these big lego brick things ever need replacing? The one that's for the fog lights is a light brown colour. Could it be this? or is something else going screwy.

Edited by KrazyKong
89CAL Grand Master

89CAL

Posted
Posted

Ok go DC Voltage (its the two lines that go straight, think one is dotted) if you dont have an auto ranging multimeter make sure it will read Volts not mV or anything like that

Put negative probe on a good chassis earth and put the positive probe into the plug with the fog light switch on.One of the terminals should have about 12V (there a 3 pin plug, should be a power for indicators, power for foglights and common earth)

So if theres power at the plug, check the earth is ok. Change the multimeter to risistance (the omega symbol) and keep the negative probe on the chassis earth and probe the terminals with the positive. You should have one of them with a low resistance (OL is outer limits and means there is no circuit, you dont want this, you want 0.0ohms or similar, it will probably show more like 6ohms or so)

If you have power and earth (I'd assume you have a good earth if your indicators still work) then there is a problem with the actually light, wether it needs a new bulb or the wiring in the light assy is a bit dodgy

If there is no power there, then post up here

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
    • joshuaho96
      Squeaking clutch/throw out bearing

      By joshuaho96 · Posted

      Yep, this bit another local owner. I caught it before putting the transmission back into the car, what I noticed was the pressure plate fingers weren't flat and even. It's more obvious with the pull style clutch because the throwout bearing ring was visibly not flat once everything is put together. Nismo should really update their instructions to call out this specific detail. I'm not even sure the clutch as-shipped orients everything properly.
×
×
  • Create New...