Jump to content
SAU Community

Red Light Camera Got Me I Think :(

KrazyKong

By KrazyKong,
in Queensland

 Share

Recommended Posts

KrazyKong Proficient

KrazyKong

Posted
  • Author
Posted

You're apparent advice has to be taken with a grain of salt to be frank. How is it that you have a chip on your shoulder, you weren't involved in my situation nor do you have any vested interest in it. You do seem though to like to post and have a go at people. And then decide they are just trolling and sit back and have a go at them some more. If you can get that worked up over someone who posts details about a situation they have gone through, when it wasn't in any way related to yourself, I'd hate to be around when something happens that is related.

So you had a go at me because I saw an orange light, did not know how long it was orange for, and thus tried to brake, but couldn't' stop before the line, and then went over the line 1 second after it turned red. Then admit you ran a red light yourself and didn't even know you had run a red light until you got a ticket. Keep your advice, it sounds like you need it more than I do.

t5iv Grand Master

t5iv

Posted
Posted

You've run a red in an area that you claim to be notorious for traffic cams.

1. You ran a red

2. You were aware that the cam was there hence how you knew that it was notorious

3. You keep reiterating the same point seeking a different result.

If you haven't had any fines in all these years, 1 red light slip up isn't going to affect you.

Still failing to see what your point in all this is.

RandomHero83 Veteran

RandomHero83

Posted
Posted

Insanity is repeating the same thing over and over expecting a different result - Einstein

You ran a red and got a fine, stop QQing like a girl and take it like a man - Me

Col Please close this thread before some of the pro trolls decide it's open season.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      GTR R34 Limp Mode

      By GTSBoy · Posted

      Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • steven7270
      GTR R34 Limp Mode

      By steven7270 · Posted

      So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Dose Pipe Sutututu
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Dose Pipe Sutututu · Posted

      Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • PranK
      Rusty roof repair

      By PranK · Posted

      Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...