Jump to content
SAU Community

Rb25Det Boost Issue

marto184

By marto184,
in Engines & Forced Induction

 Share

Recommended Posts

marto184 Collaborator

marto184

Posted
Posted

So i just bought myself a Series 2 gtst and for some reason even when my stock boost gauge is only hitting the first line above the 0 line it pops its guts out. This only happens before about 4-5000rpm. After that it seems fine... :/

Is there any specific thing that could be making this happen

Cheers

Link to comment
https://www.sau.com.au/forums/topic/400028-rb25det-boost-issue/
Share on other sites
Excuses Community Regular

Excuses

Posted
Posted

+1 to boost leaks.

+1 to missfiring, all of them cause that issue. Change your plugs ( might as well gap the. At .8 while your replacing ) and just dble check airlines, cooler piping and check to make sure the previous owner actually has the right lines from actuator and turbo.

marto184 Collaborator

marto184

Posted
  • Author
Posted

i have a turbosmart tee piece, r33 gtr sidemount, and a 3 inch system. Nothing major. I replumbed the controller from the actuator to the intake pipe myself with new vacuum line just to make sure. If i i turn the boost down it doesnt happen as bad. Ill try replacing the piping from the turbo right through.

Have just bought some bcpr6es plugs. gapped to .8 im putting them in this afternoon. should be helpful i hope :D

Daza33 Contributor

Daza33

Posted
Posted

I have a similar issue to this, don't want to start a new thread about it though.

I bought my Skyline about a month and a half ago, drove like a dream. It had yellow jackets, FMIC, pod, cat back exhaust (punched cat). I put a JJR 3" bellmouth dump on it and a turbosmart boost tee. Drove nice on 11psi, then a few weeks ago i started it up and it was missing at 4500+ rpm.

So far I have replaced plugs, gapped to .8mm, running actuator pressure boost and cleaned the AFM. Still misfires, seems to happen more in 2nd and 3rd gear. It also has a leaking turbo-dump gasket, thinking the dump flange isn't straight as I put a genuine Nissan one on it

Anyone have any ideas what it could be? Running boost off the actuator pressure it still hits about 9psi, and I have checked the coil packs already, although one had a spring that had less tension than others.

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

I have a similar issue to this, don't want to start a new thread about it though.

I bought my Skyline about a month and a half ago, drove like a dream. It had yellow jackets, FMIC, pod, cat back exhaust (punched cat). I put a JJR 3" bellmouth dump on it and a turbosmart boost tee. Drove nice on 11psi, then a few weeks ago i started it up and it was missing at 4500+ rpm.

So far I have replaced plugs, gapped to .8mm, running actuator pressure boost and cleaned the AFM. Still misfires, seems to happen more in 2nd and 3rd gear. It also has a leaking turbo-dump gasket, thinking the dump flange isn't straight as I put a genuine Nissan one on it

Anyone have any ideas what it could be? Running boost off the actuator pressure it still hits about 9psi, and I have checked the coil packs already, although one had a spring that had less tension than others.

Its ur coilpacks

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

If I increase my boost, will it lean my mixture?

Possibly. Depends how much boost and if ur tune has been done on higher boost.

The yellow jackets fail All the time. If u have any stock coil packs that work u can diagnose which one is the issue.

marto184 Collaborator

marto184

Posted
  • Author
Posted

yeah dan, i might drop into the dyno and get it done right. get it tuned to 12psi and leave it. im even planning on selling the blitz kit that i have on the car and just fitting the stock pipe back in and using the stock bov. i like the flutter sound better anyway :D

Daza33 Contributor

Daza33

Posted
Posted

Just thought id update,

got my splitfire coilpacks today, fitted em, misfire gone. I now am of the opinion that Yellow Jackets are cheap for a reason (they are shit). A guy at Just Jap told me the other week that they got their JJR Coil Packs from the same factory and they ended up binning them rather than selling em cause they had so many fail.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...