Jump to content
SAU Community

Vicroads

Stromulux

By Stromulux,
in Victoria

 Share

Recommended Posts

bluey33 Experienced

bluey33

Posted
Posted

question...

If a mechanic happens to write a RWC for a RB25 in a S Chassis. Whats stopping it going through? Say you get a dumb inspector at vicroads who identifies engine number on block to RWC engine number and thinks nothing of it as it has nissan on the coilpack cover?

Do you manually put in details on computer and it won't 'allow' to have an 'RB' engine code put in or could it be overlooked?

Link to comment
https://www.sau.com.au/forums/topic/400772-vicroads/#findComment-6366977
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

The fact VicRoads clearly list it as a VASS requirement for a non factory option engine to require a VASS?

A RWC simply does not cut it.

Whilst this thread is a novel idea - there is a EPA/RWC thread that is to be used for all questions/answers:

http://www.skylinesaustralia.com/forums/topic/156269-the-epa-threadroadworthy-thread/

Link to comment
https://www.sau.com.au/forums/topic/400772-vicroads/#findComment-6366979
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Just a standard sanding block size. With the rock chipa they are quite small. I sanded them as you could feel the edges. 
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Say you've just laid all your filler and your about to start sanding, how large is the sanding block your using?  Like a high fill primer? Technically possible but would be a nightmare. Just guessing from the photo, but they look small enough that you might get away with using a 1k spot putty. Normally you'd use something like this on pinholes but with the type of project you're working on I'd give it a go. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Omg Brake pedal removal.. FML!!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
×
×
  • Create New...