Jump to content
SAU Community

Greddy Type Rs Bov, Greddy And Turbo Timer

hixi126
 Share

Recommended Posts

hixi126 Community Regular

hixi126

Posted
Posted

1 greddy type rs bov, came of a car I bought

Measures 30mm internally and comes with an adaptor to suit

Rb25 crossover

$150 Ono posted wherever

1af1e7f9.jpg

8abbb170.jpg

2 greddy turbo timer has a scratch or 2 on it but works fine

$50 Ono posted

621ee777.jpg

fbba5cec.jpg

3 hks turbo timer in heat condition

$65 posted is in a r34 coin box( under the steering wheel) you can have the whole thing if u pay postage

44c6d56e.jpg

Stripping a r33 gtst s1 it u need anything just ask I may be able to help

simdog Collaborator

simdog

Posted
Posted (edited)

Hey,

Just a couple of questions:

Can the BOV be made into a plumb back? Ahhhh just went on the Greddy site and you can buy an outlet to replace the trumpet.

Will it bolt straight onto the same postion as the standard R33 bov?

Also when you flip the BOV over does it have a gold valve seal ring?

Thanks

Edited by simdog

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...