Jump to content
SAU Community

Recommended Posts

Hey guys,

I have picked up an r34 gtt 4 door pretty cheap. Its a 4 speed auto, lowered with pod filter and 3" cat with 120k kms on the clock. There are a few thing I need to fix up on the car, just looking for a bit of advice.

The cars throttle respose is a bit poor, one of the guys at work has had a look and inspected the car. It seems the exhaust manifold gasket needs replacing. Is this going to have much of an affect on the performance of the car? the boost still comes on but not as hard as I thought it would and it seems to be using a bit more fuel than it should. I had another person inspect the car who said the same thing was wrong.

1) Is it going to do any damage to the engine whilst driving it like this?

2) how much will getting it fixed improve the performance/economy?

3) I hear changing the manifold is a bit tricky as you have to take out a lot of the internals to get to it/ I have sourced a replacement for about $20 wholesale through coventreys, labor wise how much will it cost and how long will it take to fix?

There also seems to be a clunking sound from the front tyre on the drivers side too when you turn the wheel at low speed. Any ideas what would be causing this, and is it a cause for concern?

Pretty new to the scene, any help/advice would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/402313-r34-gtt-4-door-help/
Share on other sites

Depending on how bad the exhaust leak is, it will have a big impact on performance and response.

Less exhaust gas going into the turbo will increase spool up time, affect peak boost/ability to hold boost, and it also means less air into the turbo and out via the dump pipe, which means less air passing over the O2 sensor, which will again affect performance and fuel economy.

You've also got the problem of excess heat in the engine bay.

It shouldn't do any serious damage to keep driving it like this, but I'd still get it fixed stat.

Not sure what the difference in performance will be. Your turbo should start singing at around 2000rpm and be making full boost at or before 2500rpm.

Exhaust manifold jobs are a bit of a bitch. Usually run the risk of snapping an exhaust stud inside the head (if this does happen, don't have a crack at removing it yourself, and don't let a mate try either, just suck it up, and pay a mobile thread repair guy to come out, charge you $50/$100 and take it out in literally 5 minutes tops, nil damage). Most of the intake setup and turbo itself need to come off before the manifold can be removed. Time for the job depends, I've done it a couple of times now, and I can do it in about an hour.

I jack the car up, and unbolt the dump pipe from the downpipe. Unbolting the dump pipe from the turbo often runs the same risk of snapping bolts, as unbolting the manifold from the head. The 3 bolts from the dump pipe to the down pipe always come off hassle free.

Also, with the gasket, nuts, washers, etc. don't go aftermarket. Nothing does the job better than genuine Nissan.

It might be the best part of $150/$200, but at least it won't start leaking again 6 months down the track. I've learnt that the hard way.

Edited by Nic_A31

Cheers for the advice mate, boost isnt kicking in til about 3000rpm so your info about spool up time makes perfect sense. My boss told me the manifold studs may need replacing, his brother owns a performance shop in perth and said it can be a common problem with R34's. He also said its possible (but unlikely) there may be a crack in the manifold itself, fingeres crossed this isnt the case.

With the head studs he said I might as well replace them anyway as if the gaskets are going, everything else may not be too far behind. Problem is that you dont know whats wrong until you take everything out so you kinda have to plan for the worst.

If I supply the parts, I have been offered to have it done as a cash job at the workshop for around $200 as a cashy, does this sound like a reasonable amount? Are there any other problems I am likely to encounter?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Is it alright to top up with just another green coolant?
×
×
  • Create New...