Jump to content
SAU Community

Recommended Posts

Yea I thought the tourqe was off aswell tbh... But JEM said it should be accurate, unless I'm doing the conversion wrong of 460 ft lb?...

Does seem rather high though!...

I dunno? I know their mainline dyno reads FtLb and mine made 665 :banana:

No one apperently lol

it was just a general question and statement about r34gtrs

Haha i wasnt sure if it was me or Ant you meant!

The gains for Ants car would be impressive... Would have been nice to see a before and after graph overlayed to see the increase in the mid range :D

http://www.skylinesa...nitto-showcase/

Just saw this, i think i might go down for it.

Yeah a mate wants to go to some motorshow the day before so depending on how that goes as to wether or not i drive down to that too........... It does look good! But Sydney twice is not sounding tempting.........

are you sure its ft/lb...they only came stock with ~420N.m give or take.

If it is - thats really impressive - graph please :-)

Yea 460 ftlb..,

Will post graph when I get a chance. Very busy atm

Hey a question for the 34 GTR guys, where are the stock BOV located and whats involved in replacing them to get teh classic wank off sound as some of u call it? :yes:

take the front bumper off i beleive

should be to the left of your fmic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...