Jump to content
SAU Community

Recommended Posts

just had a thought, it would be easier for you to come over here with your one car and cruise with us, than for us to come with our many cars....

where's your sense of adventure? it's only ~3500kms...call it SAU's biggest cruise. :woot:

Plus my car already was over on your side..i'm even still rocking with nsw number plates. :yes:

where's your sense of adventure? it's only ~3500kms...call it SAU's biggest cruise. :woot:

Plus my car already was over on your side..i'm even still rocking with nsw number plates. :yes:

The guys for the SAU Nationals did it! So you have no excuse :P

funniest shit today, i call it... using a sv6 as a work ute, FAIL!

weve had construction on our rail tracks out the back and they keep driving there work vehicles over the tracks so there tools are closer, today they had a big dumper thing in to rip out all the dirt around a stretch of rail and fill it with ballast (basically rocks the size of your fist) so its stronger when locos go past.

so come 315 when the construction team is getting ready to go home and an sv6 drives over the rail when we got locos coming and the big dumper thing still right in front of him. scraps his front bar on the rail, and balast. then gets 1 rear wheel over the rail and 1 wheel outside the rail like on a diagonal, he then gets stuck in the middle of the tracks and starts single pegging on the ballast and cant move hahahaha f**kin holdens.

we got the idiot out :P

Sucks to be him

But doesn't matter what car it is they are all the same

Was doing a delivery at Woy Woy today and had to back in the driveway at the store as you do but because the pack of sheets was right at the back I had to stop short and block the entry/exit so they could get it with the forklift as there is a drain a bit further back.

the crappy forklift the store uses would get stuck on the drain if I backed the truck right in

I exit truck undo straps drop gates ready for the forklift when this muppet in a beat up Falcon ute basically parks on the footpath in front of the truck then gets the shits cause the truck is in the way

Could have easily parked next door but for some reason he leaves the ute on the footpath and blocks everyone

f**kin idiot

have dropped the price to 16500 and theres still f**k all interest, have it on ebay and have got a few people asking what the reserve is and as soon as they hear it they dont write back, have gotten an offer of a v8 statesman hahaha.

whats going on ay, its like the 6th cheapest on carsales.

car scene is DEAD!!!!

theres 5.5 days left on the ebay add with 40 watchers so hopefully someone has more then 8 grand.

hahaha yeah i wouldnt sell yours either, lots more blood sweat and tears in yours!

...maybe not tears, im a bitch. hahahahahahahah

not even getting low ballers so i thinks theres just f**k all buyers. everyone is way to responsible now days, drove to rajs corner and got so many looks in the 5 mins, take off those collars ya whipped bastards.

maybe i should put sticker on car...

Sucks to be him

But doesn't matter what car it is they are all the same

Was doing a delivery at Woy Woy today and had to back in the driveway at the store as you do but because the pack of sheets was right at the back I had to stop short and block the entry/exit so they could get it with the forklift as there is a drain a bit further back.

the crappy forklift the store uses would get stuck on the drain if I backed the truck right in

I exit truck undo straps drop gates ready for the forklift when this muppet in a beat up Falcon ute basically parks on the footpath in front of the truck then gets the shits cause the truck is in the way

Could have easily parked next door but for some reason he leaves the ute on the footpath and blocks everyone

f**kin idiot

The best way to deal with the 3 head retards in woywoy is to hit them till the stop moving then kill them with fire. ur doing the world a favor by doing this also

True

Yesterday I'm down there and twice I had p platers try and drive around the truck while I'm reversing into stores

How hard is it to wait 30 secs and let a big f**k off truck get out of the way instead of risking a lot of damage to your car

whos organising the next cruise and where to? its either martin or chookies turn to organise, unless someone else would like to have a turn and choose a route theyd like to show everyone?

u may have to stay home for the next cruise if u sell ur car mate.is anyone from newy goin to the top secret car meet at eastern creek on friday night?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...