Jump to content
SAU Community

Lakeside Raceway!

gslrallysport
 Share

Recommended Posts

gslrallysport Experienced

gslrallysport

Posted
Posted

Hey all,

As an avid supporter and someone who's really pissed off that Lakeside ever closed in the first place, and who lives all of 10 mins from it, and an hour and a half from QR, I'm asking can everyone support the 'Lakeside Motor Racing Enthusiasts' in their bid to re-open Lakeside to club level racing.

They have meetings every month and it would be great to show your support for those in QLD. Checkout:

www.lakesideraceway.com

For everybody else they've got an online petition going... if everybody could take 30sec to sign this that would be fantastic!!!

www.petitiononline.com/dnq

Remember that Lakeside twice hosted the Autralian GP and has as much history and heritage as Bathurst, and to see this class racetrack and driving training centre shutdown by some snobby shire council is fu(ked!

Thanks guys...

Link to comment
https://www.sau.com.au/forums/topic/40262-lakeside-raceway/
Share on other sites
Rolla boy Apprentice

Rolla boy

Posted
Posted

:) this really annoys me that the local councils keep closing down all the facilities for enthusiasts and then have a whinge about "hooning" problems and too many people congregating in one area. they should damn well listen to the enthusiasts for a change, instead of the old farts who complain, and they might be able to solve the problem, instead of palming it off to another area so as they dont have to deal with it.

stupid politicians, should all be kicked out. :flamed:

Link to comment
https://www.sau.com.au/forums/topic/40262-lakeside-raceway/#findComment-828225
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...