Jump to content
SAU Community

Recommended Posts

Hey guys I was just looking at the Tein japan website and the spring kits for them have different models:

For e.g. The G35 has two different spring kits available: The S-Tech and the H-Tech, the S-tech giving a lower drop than H-tech. While if you look up the 350GT it's only got the H-tech available for them and not only that, the drop isn't as low as either of the kits available for the G35. Can anybody shed some light on this? Aren't they the same car which should mean they should have the same suspension?

Note. Car is Nissan skyline V36 sedan 4 350GT 2007/ Infinit G35 Sedan 4 Door 2007

I'll give my 2 cents worth here rather than over on G35driver.... It could be that they offer a number of different models in the G35 including an all wheel drive version - they have (as far as I can tell) the base, Journey, Sport and X which is AWD. This may be the reason, perhaps others can confirm and/or deny. From what I've read on G35driver with the Tein there is a good chance you'll need a camber kit whereas with the Eibach maybe not - again probably some experience in here that can confirm.

Edited by Skylinetragic

yep the year models in the US are "wrong" compared to japan. they started 2 years behind, and somewhere later they became just 1 year behind.

usually referring to a series one or series 2 of a particular body type (35, 36, 37) if applicable will be more accurate than the actual year.

the G37 is the V36 370GT, the G35 covers our V35 and V36 350GT.

The infiniti model numbers signify the engine size not the series.. the G25 is the V36 250GT.

I think Brad is probably on the right track.. the AWD G35 will have some differences.. as far as I know the RWD G35 (up to 2006) suspension setup is the same as our V35.

the G37 is the V36 370GT, the G35 covers our V35 and V36 350GT.

The infiniti model numbers signify the engine size not the series.. the G25 is the V36 250GT.

I think Brad is probably on the right track.. the AWD G35 will have some differences.. as far as I know the RWD G35 (up to 2006) suspension setup is the same as our V35.

^^^^^^^^^^^^^^^^^^^

Hahaha there you are Brad! good to see you on here as well! Again thanks for the reply guys, so would it be safe to assume the spring kit I order from Tein Japan for a JDM V36 should fit regardless if my model is a USDM G35? Being both RWD they should right?

the G37 is the V36 370GT, the G35 covers our V35 and V36 350GT.

The infiniti model numbers signify the engine size not the series.. the G25 is the V36 250GT.

I think Brad is probably on the right track.. the AWD G35 will have some differences.. as far as I know the RWD G35 (up to 2006) suspension setup is the same as our V35.

AWD G35 is the same suspension setup as AWD M35 Stagea's (2001-2007)... either NM35 or PM35.

Hahaha there you are Brad! good to see you on here as well! Again thanks for the reply guys, so would it be safe to assume the spring kit I order from Tein Japan for a JDM V36 should fit regardless if my model is a USDM G35? Being both RWD they should right?

Same car, same suspension.

Hahaha there you are Brad! good to see you on here as well! Again thanks for the reply guys, so would it be safe to assume the spring kit I order from Tein Japan for a JDM V36 should fit regardless if my model is a USDM G35? Being both RWD they should right?

What makes you think your car is a USDM G35? I assume you have a V36 and someone has put Infiniti badges on it. You cannot import G35s into Australia, and they are all LHD.

Thanks again guys for the replies, I appreciate the input and it's cleared up my confusion on the topic.

Andrew I ordered a V36 but I asked my importer to check for me and his said it's a G35 model because he saw the analogue clock on the dash (apparently USDM only) and although it's debadged the steering wheel symbol is infinity not G35 hence the confusion.

Is it left hand drive? The clock can be added and the steering wheel changed easy enough. I am quite certain that under RAWS G35s in any form cannot be imported. Unless it is a convertible out of Europe - there are a few of those floating around - pretty sure they only started making those in 2009 though.

smoke and mirrors can turn a G35 into a V35, didnt you know? headlights arent a problem either

also youre right, there are NO USDM G35/36/37s in australia and registered. maybe there are a few track only ones.

Almost.. G35 = V35 350GT and V36 350GT (sometimes called 2nd gen G35). G37 = V36 370GT.

The Infiniti model numbers signify engine size... thus no G36 as there is no 3.6L version..

There is now an Infiniti G25.. as you can guess it is basically a V36 250GT..

Same applies for the rest of the Infiniti models.. eg. M37 is a 3.7L V6.. M56 is a 5.6L V8.. etc..

Currently true.. all G37s will look that same as our V36..

but the 2007+ G35 is also the same as our V36.. and if the next series of skyline (V37), has a 3.7L engine, it will also be called a G37 in USA. So it could be potenitally misleading to make a direct G vs V comparson.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...