Jump to content
SAU Community

Recommended Posts

Hey lads,

Stripping my cefiro down and selling all the bolt ons that were to go with it. Near everything is brand new or seen a maximum of 20,000kms.

List goes:

R33GTR Rb26 engine, has R34 N1 oil pump and rear wheel drive conversion sump, near new water pump. Has had exhaust side of things removed IE: turbos and manifolds, has had the rocker covers, timing cover and intake plenum sand blasted ready to be sprayed. Head or timing gear has not been removed so it is still sealed. Motor has done roughly 80 000kms.

Looking at $3500

Rb25 gearbox, no crunches, no gear fall outs and selects all 5 cogs.

$1500

1500KM old Garrett T04Z, T4 foor print, .86 rear with V-Band dump and anti surge drilled front housing.

$1500

Brand new 6Boost RB26 Exhaust manifold, T4 foot print with 50mm ex gate pipe

$1500

Brand new Precision 46mm wastegate, comes with all springs, V-Band clamps and V-Band flanges.

$350

Brand new RB26 JUN exhaust cam 264 degree with 9.7mm lift.

$350

Brand new HKS fuel rail to suit RB26.

$250

Brand new HKS timing belt to suit RB26.

$100

Brand new Mines Adjustable cam gears to suit RB engines.

$250

Brand new full top end cometic gasket kit, includes metal head gasket and metal exhaust gasket (87mm head gasket)

$300

Brand new tomei RB26 oil restrictor.

$20

Brand new -10 push in rocker cover breathers to suit RB26.

$50

Brand new RB26 ARP head stud kit.

$300

Brand new Tomei RB26 ornament plate ( goes on the coil pack cover )

$80

15000km old Splitfire coil packs to suit RB20/26 and series 1 RB25

$200

Brand new RB26 head breather ( pushes into the rear of the head to drain the excess oil pushed up into the top end )

$30

Unknown brand name oil cooler/relocation kit to suit RB engines. seen a few kms

$50

Monster performance front mount cooler core, no damage and has welded on mounts to fit oil cooler core.

$50

near new DEFI BF boost gauge and sensor ( no control box )

$150

Microtech LT12S with loom to suit RB26. roughly 20 000kms old

$500

ALL PRICES ARE ONO AND MORE THAN HAPPY TO DO PACKAGE DEALS BUT I WONT TAKE PEANUTS AND BANANA SKINS.

BEST TO CONTACT ME ON 0431 197 087 AS I RARELY WILL CHECK PMs.

LOCATED IN PERTH, WA

Link to pics:

http://www.skylinesaustralia.com/forums/topic/404179-rb26-motor-rb25-gearbox-and-top-notch-rb26-bolt-ons/

Also forgot to add I have brand new 1000cc Rochester top feed injectors.

Chasing $400 Ono for these

Also split fires, fuel rail, timing belt, cam gears, rocker cover breathers and oil drain spld pending payment.

I'll take the oil cooler kit , posted to 7011 , text me your bank details and price inc postage to 0419five52441 cheers

actually , did your ceff have a working speedo? If so would you be interested in selling the speedo drive? I can send you a standard 33 one plus some cash?

Edited by toffy

Update:

Cooler sold

Oil cooler sold

Ornament plate sold

Cam gears sold

Timing belt sold

Fuel rail sold

Breathers sold

Oil drain sold

Microtech sold

Throw me some offers on the rest.

cheap 26 motor with rwd sump and 25 box good for upgrades on your skyline/silvia or cefiro

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...