Jump to content
SAU Community

Recommended Posts

G'day

Hi mates, i've got a Apex'i SAFC (Bule screen one) , just wonder what is the good setting for R34 GTT?

My aim is just a little performace, because it's for daily work use. (Fuel)

This is my setting now:

*Hi-Thrti * *Low-Thrti

1000rmp+2% 1000rmp-2%

2000rmp+2% - 10%

3000rpm+2% -0%

4000rpm+3% +2%

5000rpm+4% +3%

6000rmp+5% +4%

7000rpm+2% +1%

8000rpm+2% +1%

*Throttle

LO HI

25% 50%

*Dec.air

Thr....%

Nei: 1.0%

Ne2: 1.5%

Cheers

steven

Link to comment
https://www.sau.com.au/forums/topic/40432-your-opinion-on-apexi-safc-please/
Share on other sites

You will need to tune it on a dyno and richen/lean based on your A/F ratio. You cannot just add it in with "feeling". If you get it wrong, you will definitely destroy your engine. Every car is different, exhaust, air filter, boost level, all can cause differences and therefore your setting may not be able to be used for on other cars, also you can't just plug in the numbers that your mate has on his SAFC just because the other person has an R34 GTT too.

Decceleration Air is only needed if you have an atmo-venting BOV (aftermarket).

Mine still on 0%, untuned...... trying to book a time on dyno sometime next weekend and should have a result by then. It's a R33 GTS-t though, not R34 GT-T so I dunno how are you gonna compare it.

Cost varies from place to place, but a group dyno day (run only no tuning) will cost around $50-100, and tuning maybe somewhere $100-150 onwards depends on how much needs to be done. But I don't own a workshop so ring around for prices. I could be wrong.

I have an r33 GTST with an safc, your looking around $110 an hour on the dyno + wateva you organise with the workshop for tuning, usually on the dyno for around 1 or 2 hours give or take depending on the car. Get i professionally tuned dont stuff around with it yourself, if the car runs lean you'll get detonation and you dont want that!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...