Jump to content
SAU Community

Recommended Posts

Hey guys cleaning up garage got some parts kicking around so time for them to go! It's late tonight I'll post pics tomorrow!

I have basically a complete turbo kit consisting of port matched exhaust manifolds (hpc coated black) , garrett ball bearing -10 turbos (rear housings have been hpc coated black) comes with split stainless dumps and stainless front pipe, solid stainless steel intakes for turbos gets rid of gay rubber suction pipes , factory twin turbo pipe and braided oil and water lines let's say $1500 for the whole kit

1 x rb26 block 87mm needs a deck and a slight hone $400

1 x rb26 crank machined for bearings and collar fitted and balanced (I'll try and find the bearings some where here)

$450 with bearings I'll take 50 bucks off without bearings

1x set of 87mm genuine Nissan pistons with new rings in box with factory conrods

$200

1x rb26 sump with diff and front cover been outside for a while diff probably won't be much chop

$100

If someone wants all of the engine bits they can have it all for $1000

1x full set of forged 86mm acl pistons with factory conrods great condition

$300

Also have a set of gab strut (adjustable dampning) with unknown springs the car drove very nice and smooth with these and no leaks or knocks only removed to fit hsds

$350

Please send a text with any questions on 0434 256 986

All items are located on the sunshine coast (Qld)

Thanks guys

Ryan

Link to comment
https://www.sau.com.au/forums/topic/404601-bnr32-parts-10s-rb26-block-and-more/
Share on other sites

I'll ask my builder it was a place in Brisbane jack bro's rings a bell!

Zillr the turbos have only done 5000ks on 16psi no shaft play at all! Few small nicks on the compressor wheels but nothing that will affect the performance

Also forgot to mention these have the bigger actuaters and near new cometic manifold gaskets and genuine Nissan turbo kit

Edited by rna0407

complete turbo kit

20120713_161412.jpg

genuine nissan gaskets

20120713_161417.jpg

braided lines

20120713_161423.jpg

front pipe

20120713_161431.jpg

dump pipes

20120713_161440.jpg

manifolds (one still in wraping)

20120713_161453.jpg

cometic gaskets

20120713_161457.jpg

both turbos

20120713_161504.jpg

front compressor wheel (both are very similar)

20120713_161546.jpg

rear housing (both the same)

20120713_161600.jpg

proof of authenticity

20120713_161703.jpg

rear turbo suction pipe custom one off retains all bov return etc (bov return is included)

20120713_161717.jpg

20120713_161725.jpg

front suction

20120713_161733.jpg

crank collar

20120713_161906.jpg

crank shaft

20120713_161911.jpg

factory 87mm pistons and rods all rings removed comes with new rings

20120713_161957.jpg

authenticating acl forged pistons

20120713_162101.jpg

20120713_162115.jpg

acl pistons and factory rods

20120713_162122.jpg

we all know what r32 sumps look like and also blocks

cheers ryan

  • 1 month later...

Hey guys everything is still for sale a lot of interest sorry to the people who text me and I did not reply a guy put a deposit on the turbo kit and 3 weeks later won't return my calls or texts so up it is for sale again!

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...