Jump to content
SAU Community

Where Can I Get Cam Cover Breather Pipes?

RSFOURDayz

By RSFOURDayz,
in General Maintenance

 Share

Recommended Posts

RSFOURDayz Experienced

RSFOURDayz

Posted
Posted

Hey guys, I've searched here, google and eBay looking for the black pipe/hose going from one cam cover to the other on an R34 RB25det. Happy to buy even a universal silicon hose piece but seem to find that either. Guess I'll try a bit harder but in the mean time does anyone have a source for these? Would heater hose be ok for now? (mines gone rockhard and split really bad)

Hanaldo Grand Master

Hanaldo

Posted
Posted

Any hose store?? Theoretically heater hose 'should' be ok, as it's mostly air with just a bit of vapour. But really you should get some proper oil control hose. I get mine from Hoseco. Otherwise Enzed, Pirtek, etc. etc.

Just go in and ask for 5/8 oil control hose.

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

heater hose wont work as the vapours going out of the rocker covers are hot and the hose will crap itself, as the hose is shaped your best bet is to get one from nissan,or you COULD get one from hoseco but you may have to buy a metre of it unless they have some leftover off cuts

Hanaldo Grand Master

Hanaldo

Posted
Posted (edited)

heater hose wont work as the vapours going out of the rocker covers are hot and the hose will crap itself, as the hose is shaped your best bet is to get one from nissan,or you COULD get one from hoseco but you may have to buy a metre of it unless they have some leftover off cuts

Heater hose will work as a temporary solution is what I meant.

You don't need to use the formed hose, you can rotate the breather to suit any hose. No point paying out the ass for pre-shaped hose. You can also buy half meters from Hoseco. At $18 a meter it's not too bad.

Edited by Hanaldo
RSFOURDayz Experienced

RSFOURDayz

Posted
  • Author
Posted

So is Siicon hose suitable for this? I can get the piece i need from Nizzbits for $35 delivered so I can use silicon and get it for 18 a meter like u said. Although I do like fitting genuine parts where I can.

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

go the genuine part if you can, the hose you can get from hoseco may or may not posses the heat resistance that you need. . .as a GUIDE i paid $18 for a breather (from rocker cover to rocker cover) hose for a R32 RB20DET from NISSAN. . .yes you can use heater hose as a very temp repair but why not fix it properly the first time?

Moodles2 Grand Master

Moodles2

Posted
Posted

It says it's for a RB20DET but those cam breather hoses look the same to me as RB25DET's as well (confirm the part # to be sure). http://www.kudosmotorsports.com/catalog/nissan-hose-blowby-genuine-nissan-skyline-r32-gtst-rb20det-p-581.html

ahhbee Community Regular

ahhbee

Posted
Posted

whats wrong with heater hose? ive had it on my 34 for about 4 months now since i noticed the old one had split and i cant say ive seen any ill affects at all, ive taken it on and off half a dozen times since then as well, never had any troubles or noticed any wear or anything.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Butters
      UniClutch

      By Butters · Posted

      Well they got my money but they are not getting my gearbox ! 
    • GTSBoy
      ECU sees many times the speed than speedo does (R34 swap)

      By GTSBoy · Posted

      It's needed for rolling idle up, and I think it is a decider on VCT also.
    • Kinkstaah
      ECU sees many times the speed than speedo does (R34 swap)

      By Kinkstaah · Posted

      I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...