Jump to content
SAU Community

Justin's Pie Cruise! Sept 16Th Robertson Pie Shop!


Recommended Posts

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guys, This date is pending on weather, Went and did this run again last night and it was raining, it was an absolute waste of time... So if its raining we will post pone.

Really? Are you that much of a pansy you won't drive in the rain, or is it just that your car leaks/lacks a roof?

I'd only avoid Mac Pass in extremely extremely cold weather (Like we had last friday) and it's raining, this equals snow + black ice.

Oh and in a raging thunderstorm that you really shouldn't be leaving your house because of, as it'll bring branches down.

I'm not a Pussy, I'd just rather post pone it so that Everyone can enjoy each others cars, in the nice sun like we normally get when we go up there as a club, But if this recent weather reflects on what it's going to be! All lights are green!

leave time 10 A.M or is that to early for everyone?

Hey, I'll be coming as well. Can you give me a little summary of this thread? So far I've picked up: Meet at Casula KFC @ 10AM, Sunday 16th.

Meet Car Park 9:15 Am Onwards, DRIVERS BRIEFING AT 9:45 AM! 10AM SHARP DEPARTURE TO ROBERTSON PIE SHOP VIA, HUME HIGHWAY-PICTON ROAD- MT KEIRA PASS- EXPRESSWAY TO ALBION PARK SCHOOL - MAQAURIE PASS- PIE SHOP- EITHER GO HOME OR DO JAMBEROO PASS.

Bring, Fuel, Safe Driving, freinds, Camera.. Money for Pies and other foods once we arrive. Follow the White R33 (Mine) And the Purple GTR (Owen) We Will Be Leading the cruise and sticking to the speed limits at all times, make it a nice cruise with each other no need for speed, just enjoy the roads and the company.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...