Jump to content
SAU Community

Recommended Posts

hey guys, just wondering if anyone saw this advertisement in last weeks herald sun, or 2 weeks ago about a device which gives better fuel consumption. it was in the section where the cars are sold. from memory, i think it cost $60, not sure, i've got a pretty bad memory, but it was fairly cheap. i had a quick glimpse at it and then wen i remembered about it again the paper had already gone for paper recycling day.

did anyone else see it? what sorta thing could do that for so cheap?

im damn curious, coz if it does work, i know that i'd pay $60 for it.

Link to comment
https://www.sau.com.au/forums/topic/4066-petrol-saving-device/
Share on other sites

Yeah I have one on my car, Peter Brock made it, it's called the Polariser and the fuel passes over rare earth rocks and minerals and other crud and polarises the fuel resulting in less fuel used.

Bahahahaahahha!!

If you engine is in perfect tune, reducing the amount of fuel entering without reducing the amount of air entering will destroy your engine by leaning it out.

Think about it, if it reduced consumption and improved emissions as they claim, why would the manufacturer not use these devices? Only a braindead twit would buy one of these devices for any car produced after the 80's....

Originally posted by BiteMe

This test was done on Current affairs and they showed that it increased performance and reduced emmissions. It is meant to excite the fuel atoms so they burn better. It does not restrict the amount of fuel that passes as well,

Bullsh...t................

I saw that same test.

There were actually two tests.

One was a fuel addative which didn't really work that well then there was the inline fuel filter type one which apparently did work well on the dyno and reduce emmissions by doing something to the fuel atoms.

It was extremly expensive not $60 somthing like a few hundred dollars I thought.

Its not bullshit, but the improvements were very minimal.

hence not worth laying out the money.

If you want to save money run std boost be light on the foot and run Std. Unleaded.

Well Us 32 owners can with the 8.5:1CR, I'm pretty sure you R33 owners can't but as they are prone to pinging anyhow.

I've tested my car on Std. Unleaded with 17deg timing, std ecu, full exhaust & std boost and there is no pinging.

BUT.. With the Std Exhaust it would ping a little higher in the rev's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...