Jump to content
SAU Community

Re-Installing The Standard R34 Gtr Ecu - Transponder Imobiliser Question.

GTRNUR

By GTRNUR,
in Engines & Forced Induction

 Share

Recommended Posts

GTRNUR Grand Master

GTRNUR

Posted
Posted

A friends R34 GTR power fc has an intermittent fault which is causing it to drop 2 cylinders at idle at random and reading negative air temp values on a 25 degree day. Its not just air temp being affect as well, Ive logged irregularities with the TPS and MAF sensors too.

So Ive told him to re-install his standard ecu until he can source a replacement.

I've since been told that his "mechanic" tried to do this, but the car would not start when the standard ecu was re-installed. Is it likely that this is BS, or is there some sort of proceedure that I need to be aware of to re-install the standard ECU in the car. (Injectors and coils are all standard. The car only has an exhaust and a boost controller.)

I would presume the ecu would not drop its pairing with the transponder key when the ecu is disconnected from the loom. Otherwise if a battery ever went flat in a car, the keys would need to be re-programmed all the time.

Thoughts... Suggestions?

Cheers,

Ian

paulr33 Grand Master

paulr33

Posted
Posted

its only in the supplement manual for BNR34 - i highlighted the filename at the top left

the normal R34 service manual doesnt have any info on the NATS or ATTESSA/E-TS systems

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      I am being real ocd and do not want to make amy mistakes so appreciate all help provided. I am overly cautious so asking for opinion even if i know the answer   few questions,   1.re tensioner, should spring be greased lightly?    2.tensioner has two washers , one pressure washer and other has recessed/ seat. I am going to put the recessed one facing tensioner where edges are cut out and pressure washer on top   3. my car has custom triger kit sold few years ago by guy who initially built the engine. I moved the crank gear and it moved in and out easy, only way to remove belt is to slide the crankshaft gear forward which I did. I have seen these being very tough to move , anything to do with my woodruff key?   it has a crank sensor shown in purple which I assume reads from the 12 teeth position mounted to the crankcase gear   4. timing belt doesn’t have arrow stating front or back just a arrow which I think is direction of rotation . Do you agree?   5.i figured out why my crankcase cover was worn as there was no washer installed over the crankcase cover before the harmonic balancer was put in place. It is missing, anyone knows the part number? It looks like this https://justjap.com/products/genuine-nissan-crankshaft-timing-gear-rear-plate-washer-nissan-s13-ca18-a31-r32-rb20-r33-r34-c33-c34-c35-rb25?currency=USD   https://tinypic.host/image/IMG-4535.382Zy2 https://tinypic.host/image/IMG-4537.382dSz https://tinypic.host/image/IMG-4534.382q4U  
    • TurboTapin
      New fix for low tyre pressure from bmw

      By TurboTapin · Posted

      CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Dose Pipe Sutututu
      Another little story of weird shit happening

      By Dose Pipe Sutututu · Posted

      Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • MBS206
      R34 gtt rb25det neo timing belt kit

      By MBS206 · Posted

      It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
×
×
  • Create New...