Jump to content
SAU Community

Recommended Posts

Ive got a leak from the rear of my transfer case on my 98 stagea. Not 100% sure but think its coming from where a certain hydraulic soleniod bolts on. Ive been told that this solenoid operates the clutch packs within the transfer. Im pretty clueless when it cums to these attessa awd systems so help on where to find a heap of technical info on how the solenoid works and how i would go about bleeding it would be much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/408060-transfer-case-leak/
Share on other sites

yes, there is a flare fitting where the attessa actuator line goes into the rear of the transfer case. Those types of fitting can be tricky.

If you are confident get a spanner on it, preferably a flare nut spanner, and back it off a few turns (or even all the way off). If it is off, make sure the flare surfaces are clean and then put it back in tight, but not super tight. Thread tape might help if the flare is not right on both sides, but should not be needed.

In my experience they can loosen up a little over the years, the attessa hose is big and not well supported. 80% of the time this fixes it.

There are other potential problems like damaged flare on the line (you can get a reflaring tool to even it out), and on the xfer case you can actually replace the whole flare casting if it is worn or damaged. There is also an oring which seals the casting onto the xfer case. But these are less likely to be the issue.

thanx heaps for the reply bud!

yeh im actaully a tech at a holden dealership but just hav know idea wen it cums to this attessa system. il giv that line a check but if i was to remove it how would i go about bleeding the actautor and also wat fluid does the hydraulic system use.

cheers

There is a nipple just about there where the hose joins on and actually another above the diff. Fill up the reservoir in the rh side of the boot with any quality atf and then bleed by running the engine and cracking the bleeder open and shut.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...