Jump to content
SAU Community

Recommended Posts

Apexi GT Spec Downpipe for R33 GTS-t

Model: 145-N004 9G8

  • Stainless Steel (needs a good polish for some bling brahh)
  • No dents
  • Comes with gearbox bracket
  • 80mm pipe diameter (3.15" inch)
  • I think it should Fit R32 GTS-t (please check before purchasing)
  • Comes with 2x nuts, 2x nuts, 1x exhaust gasket

Price: $150 (Will install for prospective buyer for slab of beer)

Decat Pipe/Cat Delete Pipe/Test Pipe/Defect Pipe/Flamezzzz Pipe lol

  • Mild Steel
  • Has provision to install a cover
  • Has temp sensor thread
  • Comes with 2x nuts, 2x bolts

Price: $50 (Will install for prospective buyer for slab of beer)

Location: Fairfield, NSW, 2165

Contact: PM or Reply here

Cheers,

Johnny

IMG_3326.jpg

IMG_3327.jpg

IMG_3328.jpg

Decat will fit:

C33/A31/S13/Z32/R32/R33/BNR34

Downpipe will fit:

R32/R33 most things running RB20DET

Sold:

Decat Pipe/Cat Delete Pipe/Test Pipe/Defect Pipe/Flamezzzz Pipe lol

Price: $50 (Will install for prospective buyer for slab of beer)

Still Available:

Apexi GT Spec Downpipe for R33 GTS-t

Model: 145-N004 9G8

Price: $150 (Will install for prospective buyer for slab of beer)

MONDAY (fking fail) TUESDAY bump :woot:

ALSO:

Stuff For FREE 1 [Here] - R33 ECU Passenger Kick Panel, Hand Brake Assembly & Main Cable

Stuff For FREE 2 [Here] - RB20DET Oil Cap, Oil Sump Plug, Hoses, CA18DET Hoses

Stuff For FREE 3 [Here] - 180SX Interior Bits - Trim, Cargo Straps, Washer Bottle Parts, etc.

$120 SAU Special, bring a cold 6 pack and I'll fit it too :)

MONDAY BUMP MOFOS

I'M ALSO SERZ, I SELL THIS AND I'LL BECOME A SAU NSW MEMBER TOO lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • New or used transmission? Alignment will be the same with engine running or not. If new, i'm presuming it's a clutch release bearing size issue. If used, are you certain it's a CD009/A and not an older CD008 or less? They had known synchro issues. In my opinion, these transmissions should always be purchased new, they're dirt cheap and you avoid dealing with old revisions. 
    • I like your thinking! Looking forward to see how it turns out.
    • You've got yourself a good old game of have fun. That shit is annoying as hell to remove. Thankfully for you, yours is on metal, most of the stuff I take it off is plastic, so typically hear guns are out. I normally end up continually dragging my thumb with pressure over it to get it to peel up. Eucalyptus oil then works well for getting residue and last remnants off.   Edit: plastic scraper might be worth while too. One that'll dig into the foam tape, but not scratch the paint.
    • So I ride and race motorcycles for fun and have always used a van to transport my track weapons. Figured towing a racebike with a skyline would be different and if done right could - "look fully sik" or quite cool for us grown ups lol. Pic of yours truly on two wheels I also have a trailer already kitted out to transport my bikes ...and I have a spare set of rims that match the car that I was going to rebarrel to get deeper dish at some stage but they have just been gathering dust. Sooooooo it is only logical.... Stay tuned !!    
    • If by "flap disc" you meant "chocolate wheel".... then they are OK for getting off stubborn remnants. But not for stuff with bulk depth. If by "flap disc" you meant "abrasive paint f**ker"....
×
×
  • Create New...