Jump to content
SAU Community

R34 Rb26 Long Motor/r32Gts4 Rb20 Engine/s1Rb25 Engine/ic


Recommended Posts

rb26 r34 gtr long motor,no sump or top timing cover,80000 kms,good condition,

bought this from the impound shop in act,then decided to go rb26/30 instead. $2500 slightly neg

S1 RB25 long engine still in car,(good comp,3 near new pistons,new head gasket,cam cover gasket,

timing belt kit(studs idler,tensioner and belt)new front and rear main seals,comes with inlet manifold $900 ono

R32gts4 Rb20 engine complete,was good running engine when i swapped it out for a Rb25,

been sitting for over a year now and is missing 1 oil squirter(stole it for my rb25)has engine loom but some coil plugs are brittle and broken..

$500.has a stagea sump atm but not included.Have ecu for $100 extra

Greddy return flow intercooler and Greddy pipes $300

post-43014-0-03742300-1348381424_thumb.jpg

post-43014-0-67048000-1348381501_thumb.jpg

post-43014-0-37067700-1348383023_thumb.jpg

post-43014-0-03301300-1348383282_thumb.jpg

post-43014-0-88428000-1348383327_thumb.jpg

  • 4 weeks later...
  • 2 weeks later...

a little bit interested in the fmic

not back in qld for a couple of weeks tho

does it include all the joiners?

hows the condition of the core?

  • 3 weeks later...
  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...