Jump to content
SAU Community

Recommended Posts

Hey y'all,

Time to sort my debts and life out for a little bit - selling a car i've put alot of effort into, and that will make someone very happy.

1989 Nissan Skyline R32 Sedan

Factory Silver Metallic

Engine Specs:

RB25DET NEO (Stock Internals)

ARP Head Studs

6boost Highflow 780cc Injectors

Malpassi Lift Pump

Bosch 044 Feed Pump

Modified Standard Fuel Rail

Plazmaman Inlet Manifold w/ Standard Throttle Body

Garrett GTX3076R Turbo, 0.82 Split Pulse Exhaust Housing.

600x300mmx52mm FMIC with Custom Piping

Autronic SM4 Engine Management

Splitfire Coilpacks

6Boost Forward Facing Highmount, Splitpulse Exhaust Manifold

Twin Tial MVS 38mm Wastegates (Vented for maximum drip)

ISC 52mm Alloy Radiator (SR type) with Crossover Pipe

14" SPAL Thermofan

6boost.com 3.5" Turbo Back Custom Exhaust with Magnaflow Muffler

6boost.com Custom Stainless Intercooler Piping

SARD Fuel Pressure Regulater

Custom Fuel Surge Tank/Speedflow Plumbing

Oil Cooler with Braided Lines

Greddy Catch Can

Greddy Type-S BOV

Greddy Coolant Swirl Pot

Driveline:

RB25DET Neo Gearbox

Nismo Gmax Twin Plate Clutch

R32 GTR Diff

Rebuilt R32 GTR Driveshafts & Hubs

Custom Hardy Spicer 2 Piece Tailshaft

R32 GTR Brakes F/R, Front Cross Drilled Rotors - Slotted Rear Rotors

HPI Braided Clutch Line

Cusco Brake Master Cylinder Stopper

Suspension/Steering:

CST Coilovers (8k/6k)

Driftworks Geomaster Tension Arms

Mitchy Knuckles

Joels. Modified Crossmember

Driftworks Front LCA's

Driftworks Front Upper Arms

Driftshop Rear Camber Arms

Alloy Cradle Spacers

Hicas Lock Bar

F&R Cusco Strut Braces

Whiteline Adjustable Swaybars F&R

Driftshop Tie-Rods, Tie Rod Ends

Driftshop Steering Rack Bushes

Hardrace Rear Traction Arms

GKTech Solid Steering Shaft Spacer

Bodywork/Interior

Front Wheels: 17x9"+17 Work CR-Kai (Bronze)

Rear Wheels: 17x9.5"+15 CST Hyper Zero (Bronze)

M-Spec Front Bumper

M-Spec Side Skirts

R32 GTST Chopped Bonnet

Bride Seats, Copies flamin mongrel

OMP Suede Dished Steering Wheel

Apexi EL Oil Temp, Oil Press , Water Temp & Boost Guages

Pivot Shift Lamp

Apexi AVCR EBC (Switched off, but looks pretty)

Pioneer Head Unit

Optima Dry Cell Battery

Makes 475hp on 16psi, probably a little more now but was wheelspinning on the dyno. Fullboost is at around 3600rpm. Currently tuned on E85 but easily switched back to PULP and retuned.

Car build was supported by 6boost.com and other very reputable workshops...stickers will be removed prior to sale.

Paint is a touch shabby in spots, diff is in need of tightening up/replacing. Can be road registered, selling unregistered.

Skids fourth gear without any problems.

$16,000 firm, look at the mod list.

Cheers!

PM on here, or call/sms 0422135756.

Located in Toowoomba, QLD. 1.5 hours west of Brisbane.

524294_410122822370953_1519978207_n.jpg

Matsuri3.jpg

544616da.jpg

3849c4da.jpg

Edited by 50FFT
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...