Jump to content
SAU Community

Recommended Posts

For sale - 1989 R32 skyline

Built rb26/30 by lewis engines in SA, 6boost manifold,

gt3582r turbo, 50mm turbo smart gate, vi-pec ecu and 25 gearbox

Tuned by Godzilla Motorsport in Brissy running about 380hp

Very safe tune

Quick car and very torquey car

Currently rego'd till jan next year but will be selling without roady

Much more done, car is set up for the track specifically drift any

question please call or text or message on here 0432470609

$15500 Ono I'm open to offers guys

Mainly after swaps maybe something BMW or euro maybe a v8

or something let me know what ya got, open to offers

feel free to ask questions im happy to answer

post-45830-0-28555300-1351126332_thumb.jpg

post-45830-0-99951200-1351126489_thumb.jpg

post-45830-0-85594800-1351126504_thumb.jpg

post-45830-0-50145800-1351126515_thumb.jpg

Edited by blockasR32
Link to comment
https://www.sau.com.au/forums/topic/412299-fs-r32-skyline-rb30det-26-head/
Share on other sites

  • 5 months later...

Wouldnt consider a swap for a manual R34 GTT sedan? Here's a link to an ad for pictures etc. http://www.gumtree.com.au/c-ViewAd?AdId=1006047719

Cheers :)

  • 4 weeks later...

Nissan R32 Skyline 1989 GTS-T

Engine

currently tuned by godzilla motorsports in brisbane for 380hp @ 20psi

Lewis engines built 26/30

800cc injectors

Vi-pec ecu

6Boost manifold

GT3582R turbo 1.06a/r rear housing

turbosmart 50mm wastegate

3in intercooler piping

3 and a half inch dump pipe

3in exhaust with varex muffler

poly engine mounts

rb25 manual gearbox

jim berry rebuilt os gieken twin plate clutch

10000k's since engine conversion

one piece tail shaft

kazz 1.5way lsd

56mm radiator

4in intake pipe with k&n pod filter

recirculating custom catch can

viscos engine fan and 12 inch thermo

walbro 255l/h intank fuel pump

2.5l surge tank with bosch 044 external

will come with brand new JUN 272/9.7 lift cams and JUN valve springs for the right price

suspension

hsd coilovers all round

rear camber arms

rear toe arms

hicas lock bar

front castor arms

wheels

rota grid 18x10 all round +15 offset

interior

deep dish wheel

short shifter

5in tacho

bride copy lowmax driver seat

genuine bride seat rail

stripped rear seats and belts

sony head unit

kicker amp 350.4

kenwood 5x7 front speakers

jvc 6x9 rear speakers

exterior

matte black in colour

gtr bonnet

gtr front guards

gtr head lights with HID lights

smoked gtr indicators

smoked led tail lights

car is currently registered and has been mod plated for all mods in queensland

for any more info please feel free to give me a call or text on 0432470609

thanks for your time

cheers stephen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...