Jump to content
SAU Community

Recommended Posts

Recently got a R33,

Clutch pedal feels, odd??. like the first 2/3 of travel is soft then its rather hard.

noticed its hard to get into 1st some times, if you rev out 2nd sometime it wont engage 3rd unless the pedal is near mashed into floor.

Ive tried bleeding the system, new fluid. the middle box thingy is by passed. i followed guides on here, no air in it... pretty certain anyway.

Didnt change the feel, if anything worse now. bad MC or slave?

Any other ideas? i dont really want to pull box to find its Aok.

Btw clutch doesnt seem to slip, or shudder. Friend of mine said it feels like a cracked pressure plate. the little prong bits in middle. had a similar issue with his 33.

Link to comment
https://www.sau.com.au/forums/topic/413237-odd-clutch-pedal-feel/
Share on other sites

Ahhk,

Any advice on that, havnt actually looked under there yet.

Start an apprenticeship?

lol jks. Unlock the 12mm locking nut and wind the pushrod away from the pedal (towards the master cylinder), so that you have more pushrod length between the master and pedal.

Start by doing it 1 full turn at a time. If you adjust it too far you can make it not go into gear at all.

Don't ask any more questions until you have 'actually looked under there'. Now go forth and conquer

Sorry for not "actually looked under there" , just figured id get a heads up on what im dealing with before i go f^^k it.

Not afraid to spin a spanner mate, just rather be prepared ;)

Seems my weekend is set, Camber arms, tyres, brakes, clutch, radiator and alarm setup :P

Sorry for not "actually looked under there" , just figured id get a heads up on what im dealing with before i go f^^k it.

Not afraid to spin a spanner mate, just rather be prepared ;)

Seems my weekend is set, Camber arms, tyres, brakes, clutch, radiator and alarm setup :P

Wasn't having a go at you. Just don't want to go back and forth and back and forth teaching you to do something without you actually knowing what I'm talking about. It's a waste of time otherwise.

i understand mate, i know how it works, but all cars adjust different. some have pins, some are fixed ect. just wanted to know what im up for and if i need any "specialty" tools so i can grab them during week :)

nothen worse then half in and Wahhmm, you need rarar and its sunday and shops that sell rarar's are closed :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...