Jump to content
SAU Community

Recommended Posts

Selling all the NEO parts i have that i no longer need.

Located in SA. Postage at buyers expense. PM me.

NEO / R34 RB26 CAS - $100

PB180393.jpg

NEO Coil Pack Loom, Good condition - $80

PB180394.jpg

NEO Coil Packs, 40,000kms, Good condition - $200

PB180395.jpg

S2 RB25 Throttle body (clean) - $50

PB180396.jpg

NEO Plenum, bare, sand blasted - $60

PB180397.jpg

NEO Injector Loom - $60

PB180398.jpg

NEO IAC Block, sand blasted - $70

PB180399.jpg

NEO Trac Control Throttle body - $60

PB180400.jpg

S2 RB25 / NEO AFM - $100

PB180402.jpg

NEO Injectors, Been in plastic bag since removed from engine - $100

PB180403.jpg

NEO Boost Sensor - $100

PB180406.jpg

NEO Engine cover - $50

PB180407.jpg

Brand New NEO Harmonic Balancer - $280 ($340 new from KMS)

PB180409.jpg

Brand New Clutch Fan Suit RB's - $170

PB180411.jpg

NEO Water Hoses (Brand New) - Doesn't Include All but a lot of them - $160 (Were $250 odd from Nissan)

PB180410.jpg

- Front bleed valve to thermostat housing - 14056-AA500

- Rear bleed valve to rear block t piece - 14056-AA510

- Rear bleed valve to throttle body - 14056-AA505

- Rear bleed valve to runners - 14056-AA515

- Front bleed valve to runners - 14056-AA520

Tomei INLET Adjustable timing gear - $150 Including postage.

2012-08-10_16-38-20_4451.jpg

NEO Pistons and Rods - $100 good nic - Rods are the same as RB26 rods

P6110304.jpg

Link to comment
https://www.sau.com.au/forums/topic/414069-rb25-neo-parts-for-sale/
Share on other sites

  • 2 weeks later...

Have you worked out if you need it?

Sorry for the late reply. I honestly havn't worked it out if i need it or not.

Do you know the precise reason for it? I know it controls the valve for the purge canister. But why did the NEO have this ECU controlled solenoid valve and all other RB's did not?

Bump btw.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...