Jump to content
SAU Community

Recommended Posts

Hi,

I have just upgraded injectors (nothing rly else that would affect anything) on my R34 GTT. I have nistune and so i changed the k constant by going through the injector resize option and changed from 725cc to 1000cc.

This brought the k constant down from like 394 to 285. Problem is my air fuel gauge shows about 20 on the gauge and it runs pretty choppy. If i move the k constant up closer back to 394 originally the AFRs drop down back to closer to 14.7.

But if i rev it just a tiny bit it jumps up again.

Any suggestion would be appreciative! Just trying to get the car able to be moved to the tuners 350km away.

It already had an existing tune and ran no problem.

Thanks :)

Injector latency is different even between same brand. An example is this pair (Denso made injectors). Sard 700cc 0.65msec, Sard 800cc 0.75msec.. so you can imagine the latency difference between 725cc and 1000cc.

Bring you min injector on time up a little - they are probably be operated outside the non linear range of the injector... Unfortunately it is not an exact science... Especially when your not taking into account latency.

Edited by rob82

Hey guys yeah you were right thanks jacked the latency to 1030. Now its idling perfect at ~ 14.7 AFR and rest of the rev range looks good. Might read a bit more instructions next time ;) There wont be any damages having 20AFR on idle ? Also not having narrowband plugged in is also okay on a 350km trip ?

Narrowband sensors get damaged when they're not powered as the heater can't burn off deposits. It sounds like you're using Nistune, there's are afew ways to ignore O2 feedback, one of them is to set the minimum engine temperature which the ECU will accept O2 feedback (defaults at 30C) to something high 200C where the engine has no chance of getting that hot, this way they will at least be powered.

I have my wideband in its place at the moment, so its not connected at all or screwed inside the dump. I prefer to keep the wideband so i can monitor AFRs on the way there, also just read that i can solder some wires to the ecu to simulatre narrowband signal :O. Its MTXL Innovate one. Or since the AFRs are okay i can just plug in the narrowband so cruise is okay and hope not issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...