Jump to content
SAU Community

Recommended Posts

Thinking of splitting the ceffy, so if I can get the motor, box and shell gone I'll split it all out. Everything can be seen running and will take offers on individual parts.

A31 1990 Cefiro shell: $3800ono

Painted a custom gtr grey

All interior in mint condition

Hydraulic handbrake plumber with hard lines

Full 5stud conversion

Currently registered and complied, no defects

Origin roof Wing

All electrics work

R32 front seats

All boot carpet etc

All trims

Rebuilt power steering by fulcrum rack (2months

old)

Rebuilt brake master cyclinder

All adjustable arms

Engine: 1800ono

Rb25det series ones

Cosmetic head gasket

Arp head studs

Custom water lines

Head was decked and cleaned when head gasket was out it

6boost hi flowed 780cc injectors

Spit fire coil packs

Every seal and gasket about the block has been replaced

Stainless piping to suit intake plenum

Clutch: $300

Excedy sport ceramic, 3puk rebuilt by npc before matsuri and up-graded, will come with flywheel

Gearbox: $1500ono

Rb25det series 1, always ran redline shockproof lightweight, feel mint.

Turbo setup $2000ono

Only used for matsuri, made 396hp on 16psi

Garrett 3076r .63

Turbosmart hypergate 45mm 10psi spring

All custom lines (braided and hard)

Xforce hi mount manifold with stainless screamer

Power fc computer $1000.

Juzzo 0421324648

624F913C-E9F9-4235-A1FA-AE6FA447698A-15098-00000D3836D6A1E7.jpg

097C987C-C606-4ED3-9507-526B70D7ACEF-3348-000003E5A6BBD7B8.jpg

32E5ECD7-87FB-4786-A932-0100B8F31598-5234-00000510A51BC8BA.jpg

Link to comment
https://www.sau.com.au/forums/topic/414949-qld-a31-cefiro-part-out-rb25det/
Share on other sites

I would take the gearstick plastic surround aswell as the plastic surround for the radio.

Picture of Origin roof spoiler would be nice too!

I would take the gearstick plastic surround aswell as the plastic surround for the radio.

Picture of Origin roof spoiler would be nice too!

Wont be splitting little things like that. May split any aftermarket parts. Will get pics of the roof spoiler this week

I posted a reply in your other thread, but I can't remember if I sent you a PM at the same time or not....lol was in regards to the filter relocation kit.

  • 2 months later...

gday there juzzo , how are ya bud , just wandering would you have a stock a31 bonnet and plastic front grill for sale man , as for the boot carpet and drivers side door trim ?

let me know champ

thanks heaps

anthony

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...