Jump to content
SAU Community

Recommended Posts

My R32 GT-R lands in the next few months from Japan, It's been sitting in a Car Yard for 8 months untouched.

I have a fairly apt mechanical knowledge, I can with some help from a friend change timing belts - adjust the timing, oil, oil filters.

So basically I have an R32 GT-R coming off from the docks that hasn't been touched for 8 months, provided the engine doesn't need some work what is there to be done?

I'm thinking.

  • Oil
  • Oil Filter
  • Timing Belt
  • Compression Test
  • All other oil (Differential ETC...)

Any to add? What are your thoughts?

Thanks Gary.

Link to comment
https://www.sau.com.au/forums/topic/41544-first-things-first/
Share on other sites

Change the battery, tyres will be rooted if the cars sat there for 8 months without moving, change the fluids, you may aswell change every single fluid and oil in the car for compleate peice of mind, i mean its a gtr!, give it a little lovin :rofl:

Arent you scared that a car that looks that low might get the kit smashed by some useless warfies that just dont care?

Sumo

Welcome to the world of importing cars, this rarely happens the wharfies are actually very good, it's only a handful that resort to thievery.

This is my friends FC, it was in the same yard in Japan as my GT-R, it is lower then my GT-R

http://iliketomoveitmoveit.com/disp_pic2.jpg

thats a picture of it in sydney and you can barely fit your foot underneath it, came off the boat without a scratch, it's a roll on - roll off system and Kiwi gives me insurance as well.

More than likely you'll find the Japanese owner has decided to forego some routine maintenance. Also alot of suspension bushes and so forth will need replacing, waterpump, oil pump, belts, wiring... all little issues which will come into play :(

Btw, your oil sender may need replacing :D

Change the battery, tyres will be rooted if the cars sat there for 8 months without moving,

Aside from being illegal to use the tyres that are on it anyway, why will the tyres be "rooted" if they haven't moved in 8 months? Presuming they aren't flat.

ya, wasnt thinking, dont tyres get flat spots if there left in the same postition for ages?

Ummm NO....

They can become hard due to going through heat cycles and sitting dormant but that usually takes longer than 8 months...I would be investing in some new tyres though...

Other things to consider are plugs replacement, and oil/engine flush BEFORE putting in new oil, and a good coolant flush, ie through the heater hoses etc...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey   ive gone for a terminated harness on my build so selling brand new unused and unopened piggy back harness  https://www.haltech.com/product/ht-141357-elite-2000-2500-nissan-skyline-r32-33-r34-gt-r/ Located Bathurst NSW   price $600 + postage     
    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
×
×
  • Create New...