Jump to content
SAU Community

Recommended Posts

Washing the Micra this eve after driving it from Point Hut road all through the Cotter area. (wow some mad changes have gone down since I last went through there)

Skyline wash tomorrow.

Got the dremel out and put the n1 vents in today.

The Nissan ones are lovely, nice paint job on them already, and they just clip in if you make the hole right.

post-89755-0-73573600-1364542280_thumb.jpg

Reminds me why i like Japanese made stuff.

Washed her.

Also went and picked paint up to do the front bar of the Foz and was going to spray it today.

But after finishing washing the GTR I cant be bothered. I will do it tomorrow avo.

How many cans did you get? I always seem to under estimate :/ Did you get it from Capital?

Did some more wheel cleanings. *sigh* still needs more attention.

Filled up @ $1.70.9 / Litre :O

Rear ended a Holden Cruise with no evidence of impact other than a chicks name, phone number and a memory of cleavage. :D

Too late to wash the Liner now... Must do in the morning.

Tried to fit the greddy oil cooler to the 34 designed to go in front of the radiator however my big ol' front mount appears to be in the way so I think I'll have to fab up some mounts and put it in the drivers side of the front bar.

Also used my car to rip a tree stump out of the ground.

Probably the most useful thing my car has done since I bought it.

How'd it turn out Eric ?

Likely will wash/polish car after yesterdays run.

Picked up 2 minor chips in the windscreen, from oncoming cars yesterday, so will try polish them out with some stuff I have.

Then I think a good movie and some munchies this afternoon :D

Any recomendations ?

Grammar

Richard, I can recommend pork belly.

I already know pork belly Richard intimately. Thanks for the referral tho - LOL :thumbsup:

It turned out pretty good. Will look much better once I blend the edges out. Taking for inspection tomorrow, then register....then sell!

I can reccommend pork belly Richard. LOL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...