Jump to content
SAU Community

Recommended Posts

Set of Genuine Volk GT-C's in silver, 17x8 +35 Face 1 and 18x9 +38 Face 2. Fronts in excellent condition, rears have a few small marks on the chrome lip, nothing major though.

Front tyres are stuffed, Rears have 245/40 Potenzas with a 1mm or so left.

Includes a set of genuine wheel/lock nuts which you will need to run these!! Thread is 1.25.

$850 Need these gone ASAP!!!!

Well under the price i want for them but i need them gone!

Due to work i cannot organise freight interstate, buyer must organise. Prefer local pick up.

Contact me on 0407 633 573 for more pics.

post-48830-0-24065800-1355556057_thumb.jpeg

post-48830-0-08095300-1355556072_thumb.jpeg

post-48830-0-15626700-1355556232_thumb.jpg

post-48830-0-70515200-1355556333_thumb.jpg

post-48830-0-75739600-1355556473_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/415680-sa-volk-gt-c-wheels-cheap/
Share on other sites

Bump!!

For anyone who is interested, please don't msg me and offer $400 like some idiot did, not interested in dealing with people who think bob jane make better wheels!.. Thanks :)

  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...