Jump to content
SAU Community

Recommended Posts

that the details of it, looks like it would be worth a try for $100

UP FOR AUCTION IS FOR ONE PERFORMANCE TUNE TO CONVERT YOUR NON TURBO N/A ECU TO TURBO,,,, GAIN 10 KWs AT THE REAR WHEELS ITS A 95-98 OCTANE TUNE AND LETS YOU GET THE BEST OUT OF A VL WITH AN INTERCOOLER FITTED AND MORE PSI .. THIS IS ALSO IDEAL FOR A HI COMP TURBO CONVERSION WITH NO KNOCK SENSOR ETC JUST A TURBO / TURBO INJECTORS AND PREM FUEL IS NEEDED..

FITTING INSTRUCTIONS ARE SUPPLIED

REQUIRES YOUR STOCK N/A ROM TO BE UNSOLDERED AND THE NEW SOCKET SUPPLIED FITTED THEN YOU CAN PLUG THE NEW TURBO PERFORMANCE EPROM IN ,

ONCE CONVERTED YOU MUST RUN VL TURBO BROWN TOP INJECTORS AS THE N/A TYPES WILL NO LONGER RUN,

ONCE FITTED YOU WILL BE NOW RUNNING TURBO FUEL AND IGNITION MAPS + HIGHER FUEL CUT ,

dont know lol spose ill give it a shot and put it on the dyno and see how it goes , yeah i did got a hight mount turbo is the same size as a 35/40, 50mm gate ajustable fuel reg and front mount just need too do injectors and ecu but dont want too spend too much

So you have a ebay copy turbo and a ebay copy gate/manifold?

ebay special chip sounds like it'll fit in nicely!

However if it were me, it's $100 wasted. Better off putting it into the pokies. A proper tune/ECU will cost $2000+ - fact of life.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...