Jump to content
SAU Community

Recommended Posts

rb25det series 1 afm green label great upgrade for rb26 I've got 2

$60 or 100 for both

r33 gtst rear 5 stud conversion

hubs

rotors

calipers etc

$200

r33 gtst front hubs, rotors and brakes good for 5 stud

$200

r33 gtst drive shafts

great condition

$40ea

r33 rear cradle just the cradle

$20

r33 r34 king springs

$50

r33 gtst brake master complete non abs

great condition

$20

r33 manual conversion

comes with everything

Rb25 gearbox

one peice tailshaft

bradied line

both pedals

slave and master cylinders

clutch

flywheel

$1500

r33 engine crossmember perfect for rb conversions

$70

R33 power steer rack

Great condition

$40

R33 rear factory strut brace

$20

r33 front sway bar

$20

r33 series 1 behind the dash aircon stuff

make a offer

r33 series 1 window trims from door and car the one that always fade

make a offer

r33 overflow bottle

$10

r33 gtst turbo back 3inch exhaust

$150

r33 fibreglass rear bar looks awesome

prefitted just needs to be painted

$30

R33 gtst ignition barrel and locks with key

Good condition

$130

R33 gtst side mirrors

$20 each

r33 passenger side gaurd with blinker

maroon

$20

R33 series 1 dash

$30

R33 gtst centre console

Good condition

$20

R33 doors complete with glass and wiondow reg etc only missing the door trims

Will separate

good condition

$50 each

R33 gtst tail lights

Great condition

$20 each

R33 glovebox

$20

R33 boot with aftermarket wing/spoiler looks similiar to standard one lights up skyline

$20

R33 handbrake with full handbrake cable to hubs

$30

R33 passenger window reg motor

$35

R33 passenger window switch

$20

R33 bonnet latch and cable

$30

R33 bonnet latch bracket

$20

r33 boot and fuel flap latch assembly

$20

r33 air con unit/display

$20

R33 complete air con set up with everything!

condenser

compressor

dryer

lines etc

$130

i have all the interior plastics etc

So much more just can't think text me or pm me if you need anything

Gold Coast can post

0487924497

Link to comment
https://www.sau.com.au/forums/topic/416528-r33-s1-parts-wrecking-2-cars/
Share on other sites

hey mate do you have the under dash part of the AC? the evaporator is the part we are after as ours is leaking

also what are the king springs you have? we have a stock R33 S1 4 door and want to lower it a bit

can pick up no dramas

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...