Jump to content
SAU Community

Recommended Posts

Adam - that's nice average power.

When my R33 was stock I get 145 rwkw with just a zorst & pod.

So 162 with auto is pretty good, I'd say. What is the boost set to ?

What does the seat of your pants say ?? Can you feel the difference ??

Meggala,Yeah I am. I can feel that flat spot but I haven't had a chance to drive it properly yet since the AVC-R went in on friday. Makes me wonder about all these guys with 200 and 250 rwkw though.

Obviously I know that I have an auto and there are power losses there but that was my choice for comfort in Sh!tney traffic.

Here are my first dyno sheets.  Car is an R34 GTT auto with full exhaust and AVC-R boost controller.

 

What do people think?  Is this alright?

looks good adam. with the tiptronic gearbox i think you should be reading slightly higher than manuals because of gear ratios. and i also believe auto/tiptronics have a different ecu....but dont quote me on that :P from memory (i'll have to dig it up) i got 154kw on the same dyno with about the same amount of mods.

1 tip - FMIC. i didnt notice any seat of the pants difference and thus that represented zero bang for dollar!!! for a street car, i think the side mount is perfect for power levels close to 200rwkw. when you do some trackwork or get a bigger turbo then i think this is where a FMIC starts to get important.

spend your money on a handling pack from say whiteline. what are you after? track stuff? street?

3rd gear for me and 4th for you is 1:1 but I'm not sure if this takes into account the diff or not.

I do like the track which is why I thought about getting the FMIC. I'm also leaning towards whiteline for suspension.

I've got to get some decent tyres too.

Robo: Yeah they certainly seemed to wring it's neck on the dyno didn't they. I went to 7k last night when I miss pressed the button to change into 2nd gear. It didn't seem to hit any rev limiter.

Franks: I was going from memory but I think it touched that mark once at Eastern Creek. The rest of the time it stay a little under that even after 15 minutes on the track. It behaves so well. Brakes never fade, never overheats, once got at A/T light to go on but that was at the end of a track session with the last two laps basically being drift laps at Wakefield the other day.

Benm: seems it took 5.5 hours :)

I had a proper drive last night and that flat spot is quite annoying but the rest of it... mmmm... power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...