Jump to content
SAU Community

Recommended Posts

Part:

RB26/30 long motor

Condition:

Built but never run :(

Description:

Typical story, got rid of project car due to purchase of house and the wife was pregnant with my first child...now the wife is pregnant with the second kid and I have a bathroom that desperately needs to be redone.

All up I remember spending around the $14,000 mark, so my loss is your gain.

More info:

- A8 block (bored, honed, decked)

- R32 GTR head

- HKS gaskets

- Head cleaned and serviced

- shot peened and linished conrods

- Crank/oil pump collar

- Crank balanced

- rotating assembly balanced, crank grub screwed and fitted with colar

- ACL forged pistons

- ACL bearings

- GTR Oil and water pumps

- HKS adjustable cam gears

- HKS cams, unknown model...didn't think to check before delivering to builder and he said he couldn't find a model number on them.

There are bits missing from the motor, including all the AAC gear, loom, valley and cam covers...This would be the perfect upgrade for someone that already has an RB26 that is looking for a bigger bottom end.

8.8:1 static compression (quite high for a 26/30) this was from my request during the build for better off boost driveability, I can't remember the exact combination that we used to get there, but it also included decking the block a little. Feel free to post questions, but remember it was a while ago now so my memory is a little vague

Location:

Blacktown, NSW

Contact Details:

[email protected]

PM on this site

I'll include my mobile number to serious people

Asking Price:

Looking for offers above $6,000...feel like I'm low balling myself

Or, feel free to offer something of interest...you never know

Pick-up/Postage Arrangements:

I'm willing to transport it inside the Sydney area...but you'll owe me a beer when I get there

Link to comment
https://www.sau.com.au/forums/topic/417541-rb2630-long-motor/
Share on other sites

I'm not interested in separating, sorry.

No photos of the build, it was done by MRC Dyno Services (Castle Hill, NSW)

I've got 2 of the 3 receipts (lost the first one)

http://i225.photobuc...8may09page1.jpg

http://i225.photobuc...8may09page2.jpg

Images of the long motor

http://i225.photobuc...fsomecovers.jpg

http://i225.photobuc...ginebuilder.jpg

http://i225.photobuc...26inletside.jpg

It also comes with the throttle bodies, inlet plenum, half the loom (been hacked up, probably better thrown away)

EDIT: The harmonic balancer is from an R31 Skyline

Edited by NXGriffo

Anyone recovered from buyer's remorse after the Christmas Period? Maybe you'd like another round of spending...look no further, beef up that Skyline with a properly built 26/30, not just another slap together hybrid.

  • 4 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 years later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...