Jump to content
SAU Community

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

For less than $10 replace that radiator cap and go from there.

Its the cause of many symptoms like this for skyline owners and is such an easy and cheap 1st option for troubleshooting.

Especially as you ahve the symptom of the top hose not getting super hard at normal operating temp...

That and follow this description on fully and confidently bleeding a skyline's infamous cooling system of air

(10th post down)

http://www.skylinesaustralia.com/forums/topic/406363-coolant-reservoir-problem-or-not/page__p__6476678__hl__cut%20bottle__fromsearch__1#entry6476678

Yeah I've read through that before when I had my 33s, This is a CA S13, so no bleed screw but I've pretty much done all the other steps.

I might look into a radiator cap for cheap insurance.

I'll know more this weekend when I've had some time to fiddle.

When the pressure test shows it's holding good pressure the next link in the chain is the cap not holding up.

For less than $10 replace that radiator cap and go from there.

Its the cause of many symptoms like this for skyline owners and is such an easy and cheap 1st option for troubleshooting.

Especially as you ahve the symptom of the top hose not getting super hard at normal operating temp...

That and follow this description on fully and confidently bleeding a skyline's infamous cooling system of air

(10th post down)

http://www.skylinesa..._1#entry6476678

I'm not having a go but you can improve your bleeding method a lot with a couple of small changes. First is you don't need to jack the front of the car up, the system is designed so the bubbles move towards the radiator and bleed screw easily on level ground.

Second is you should undo the bleed screw when first filling the system to let the displaced air escape. You keep filling the system until it comes out of the bleeder, only then you start the car and top up as necessary.

No offense taken mate, all advice is always welcome.

This is a CA18 so there is no bleed screw as was mentioned earlier which is what makes this system one of the trickier ones.

I'll keep at it and report back how I go. My main concern is that the head is sealing properly.

No that was for jjman.

All you have to do if keep the radiator topped up. Another thing is to take it for a drive once you've finished. Once it has cooled down check the overflow level because it would've sucked some coolant in. Top it up to max level and keep an eye on it to make sure it doesn't keep on droppiing. If it does then you have a leak.

Ahh, OK.

Yeah I've got a rough idea on what needs to be done so I'll test out all the theories when I dump the coolant this weekend to remove the stuff that was oil contaminated from the HG failure.

When the pressure test shows it's holding good pressure the next link in the chain is the cap not holding up.

I'm not having a go but you can improve your bleeding method a lot with a couple of small changes. First is you don't need to jack the front of the car up, the system is designed so the bubbles move towards the radiator and bleed screw easily on level ground.

Second is you should undo the bleed screw when first filling the system to let the displaced air escape. You keep filling the system until it comes out of the bleeder, only then you start the car and top up as necessary.

hey, yeah while ill agree that thats an adequate way to do it iv found it not to be consistent as well as quick (if u have 2 jacks/hydraulic jacks) and foolproof, as iv found this method.

The RB25 is notoriously hard to get all the air out of,even with the bleed screw. Twice iv had my car come back from the mechanics (import specialists) with air still in the cooling system (and coolant mess around the bleed screw)

Iv found this way the only sure way to do it first time every time.

Which is the reason i always recommend it to people who are troubleshooting their cooling system because ruling out an air lock in the cooling system as a symptom of a problem (one of the easier things to do alongside radiator cap) is the best place to start. And the amount of people iv seen bleed an RB the standard way and still have air in the system and still left scratching their heads and going back to the drawing board when this was thier only problem or at the least it still prevented them from being able to see the true problem.

Edited by jjman

No luck today, tightened a few more things but there still seems to be a very slow leak.

I can no longer see any coolant leaking (exception being a very tiny weep from one turbo line when the car is warmed up), just the gauge dropping slowly.

I also still got the gurgle after driving it.

Working on the car at the moment, just stopping for lunch and waiting for it to cool down.

Emptied out the radiator and ran the engine with clean water flowing in while watching the water flowing out.

Plugged it up and put a bottle of radiator flush in it, filled it up and let it idle for a good 25mins.

Towards the end it started frothing up as shown. I'm assuming this occurs as the radiator flush does its work.

Once it's cooled I'll flush it again then put new coolant in it, no doubt it'll take a while to bleed out the air but at least once I'm done the coolant should be clean enough for me to TK test it if needed.

post-23873-0-87877500-1359337434_thumb.jpg

OK done for the day as I'm a bit over it now.

Flushed out all the radiator flush stuff, ran the car for a solid 25 mins, jacked up and levelled out with the top radiator hose disconnected and waited for the water to run clear. I had the heater on the whole time on full.

I let the car idle for a few minutes without anything in the radiator just to pump out the last of the fluid then reconnected the top hose and filled the radiator with coolant. After filling the radiator and the overflow tank it only took 4L of fluid, though the FSM says the system takes 7L.

I let it idle way up on the jack for quite a while to free up any air bubbles then took it for a drive. Temperatures were stable and the heater worked fine.

After coming back it still gurgled from the same spot, not for long though, and I got under it and still can't find any obvious coolant leaks with the exception of a very tiny weep at one turbo line.

After letting the car cool down, it looks to have drawn a little coolant from the overflow and there appears to be a little bit of sediment sitting on top of the coolant in the radiator, nothing serious though.

I'll drive it a few more times and get it hot/cool it down and see if the overflow levels out after a while. I still have the pressure tester also.

Spent some more time on it tonight and thought I'd test the tester.

I inflated the bladder in the neck of the radiator and just let that sit, low and behold the gauge started dropping so I'd say the tester has a leak of its own.

I pressurised the system fully and looked for leaks again, only one I can find is that tiny weep from the braided turbo line so I'm not super worried about that.

I'll drive it some more and see what the coolant level does and go from there.

id say if it is leaking then fix it. Gotta rule out the obvious to be sure of narrowing down a problem...

sorry to be the bearer of bad news but its likely that its the rubber hose that attaches to that braided line. prick of a job (unless you have some decent tools).

It's weeping at the fitting, where the line joins the banjo fitting on the turbo. It's the outside line also and very easy to access on my setup, I can remove it, but of course it will piss coolant out everywhere during the process.

I'd ay I'd have to get a hydraulics place to remove the end and re-crimp/attach whatever it is they do.

Drove it last night, no gurgle that I could hear when I got back, but the coolant level had dropped a small amount in the overflow over night.

I'll have to fix that braided line to rule that out too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...