Jump to content
SAU Community

Recommended Posts

Includes,

2x HKS GT-RS Turbos

2x HKS Actuators

Have invoice from Garage Whifbitz where they where bought 2011-06-02 and they have done less than 7,000km since, mint condition.

Picture below also shows oil/water lines and bolts but these are Not included, if you are moving from OEM, HKS or Garret twin turbo system your current ones will fit.

Looking for $1,700 (AUD) plus shipping

turbokit_small.jpg

Christian

Link to comment
https://www.sau.com.au/forums/topic/419577-hks-gt-rs-turbo-kit/
Share on other sites

Cheers mate, I have had a few people interested so far but no payments or reservations. I will include a copy of the original receipt that shows they were bought for 3,300 UK pounds! that makes this hell of a bargain

I´m located in Sweden and preliminary shipping cost to Australia is $300 AUD but need to check this using byer’s final address

edit,

Forgot to mention that while these were mounted in the car they ran 0.8 bar of boost.

Edited by Christian P
  • 2 weeks later...

Because ur overseas mate makes it hard

Put a link to eBay with PayPal as payment they will sell like hotcakes

Turns out Ebay only accepts ads up to 650 dollars per mounth.

But for everyones information I do take paypal

  • 1 month later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...