Jump to content
SAU Community

Recommended Posts

ive searched and read through afew different threads but couldnt find the info im after.

on my old r32 i put an rb25 turbo on my rb20 and just drilled and put a tap on the front housing.

now im going to put my spare rb25 turbo i got laying around on my rb20 in my current r32.

just wondering how else others have ran there boost lines with out having to use the r33 boost solenoid or boost controller on their rb20's.

thanks

Link to comment
https://www.sau.com.au/forums/topic/420156-rb25-turbo-on-rb20/
Share on other sites

haha left that part out , how else have they been installed with out drilling the front housing and adding a tap like i did the first time i did it.

is there a way to install them with out having to do it like i previously did , and can it be done with out using the r33 boost solenoid or a boost controller.

You either need to to drill and tap the housing or weld on a tapping point on the hot side intercooler pipe (preferably at the turbo outlet end of the pipe). Not really any other option than to source a boost reference from there. Don't listen to anyone who tells you to get it off the plenum.

Yes it can be done without any boost controller at all - just run a hose direct from boost reference location to actuator**. You will get whatever the R33 actuator is set to give (5 or 7 psi). If you want more, then you either need some sort of boost controller or you need an R32 actuator (which will give you ~10 psi). The R33 solenoid will do you no good on an R32 as the ECU doesn't know what to do with it.

**this is exactly how my Neo25 is set up at the moment in R32 until I get it inspected and can put the boost controller back on.

Edited by GTSBoy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...