Jump to content
SAU Community

Recommended Posts

Wrecking a 1998 R34 GTT Coupe. All parts are available minus the engine with ancillaries and gearbox. All parts are in good working condition unless stated otherwise.

Pick-up is from Emerald, Victoria and postage is available for items which meet Auspost size/weight restrictions.

1. Complete engine loom and computer - $250

http://i160.photobucket.com/albums/t177/Shano3000/P1040211.jpg

2. Front brake calipers and rotors, plenty of meat left on both pads and rotors - $300

http://i160.photobucket.com/albums/t177/Shano3000/P1040176.jpg

3. Rear brake calipers and rotors, plenty of meat left on both pads and rotors - $200

http://i160.photobucket.com/albums/t177/Shano3000/P1040222.jpg

4. Factory 17" wheels. Very good condition with only minor gutter rash. Tyres are 98% new Triangle, TR967, 235/45/ZR17. If you're ready for new tyres on your stock R34 GTT rims would be cheaper to buy these, then onsell your rims - $450

http://i160.photobucket.com/albums/t177/Shano3000/P1040204.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040205.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040206.jpg

5. Rear subframe with diff. Includes rear cradle, diff, drive shafts, hicas, hubs, suspension components and handbrake assembly. Rear brakes have been removed - $350

http://i160.photobucket.com/albums/t177/Shano3000/P1040224.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040226.jpg

6. 3" complete turbo back exhaust. Includes 3" Cat back exhaust with cannon muffler and silencer, 3" Cateran high flow catalytic converter and 3" bell mouth dump/front pipe. Has some scratches on the muffler and dints in the silencer. Muffler tip has been shortened. Complete bolt in system - $370

http://i160.photobucket.com/albums/t177/Shano3000/P1040184.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040185.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040186.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040187.jpg

7. Factory front bar. Structurally in good condition, paint has blemishes as shown in pictures. Middle air vents have been removed for FMIC placement - $300

http://i160.photobucket.com/albums/t177/Shano3000/P1040156.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040155.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040157.jpg

8. Factory struts, complete set - $200

http://i160.photobucket.com/albums/t177/Shano3000/P1040215.jpg

9. Factory front adjustable strut brace - $50

http://i160.photobucket.com/albums/t177/Shano3000/P1040183.jpg

10. Excedy replacement clutch. minimal use, would estimate at 90%+ meat left on clutch plate. No scoring on pressure plate. Comes without thrust bearing - $300

http://i160.photobucket.com/albums/t177/Shano3000/P1040241.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040240.jpg

11. Flywheel. No scoring - $70

http://i160.photobucket.com/albums/t177/Shano3000/P1040242.jpg

12. Tail shaft (Manual) - $150

http://i160.photobucket.com/albums/t177/Shano3000/P1040154.jpg

13. Gearbox X-member - $50

http://i160.photobucket.com/albums/t177/Shano3000/P1040195.jpg

12. Manual pedal setup with clutch slave/master cylinders and lines. Includes clutch and brake pedal for conversion - $200

http://i160.photobucket.com/albums/t177/Shano3000/P1040212.jpg

13. Power window motors. Left and right hand side (Coupe) - $100each

http://i160.photobucket.com/albums/t177/Shano3000/P1040161.jpg

14. Ignition, locks and key set. Includes ignition barrel, L+R door locks, boot lock and original factory key - $220

http://i160.photobucket.com/albums/t177/Shano3000/P1040175.jpg

15. Door shells. Painted white, locks and window motors have been removed. Glass included. Passengers door has 2 small pin dents - $100each

http://i160.photobucket.com/albums/t177/Shano3000/P1040198.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040199.jpg

16. Drivers side power window switches and surround - $80

http://i160.photobucket.com/albums/t177/Shano3000/P1040163.jpg

17. Passenger side power window switch and surround - $30

http://i160.photobucket.com/albums/t177/Shano3000/P1040169.jpg

18. Mirrors. Painted white. Passenger side has 2 small marks in the paint as shown in picture - $50 drivers and $40 passenger

http://i160.photobucket.com/albums/t177/Shano3000/P1040171.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040172.jpg

19. Steering rack - $100

http://i160.photobucket.com/albums/t177/Shano3000/P1040158.jpg

20. Indicator and wiper stalks with steering lock mechanism - $50

http://i160.photobucket.com/albums/t177/Shano3000/P1040202.jpg

21. Steering wheel with airbag. Has minor signs of wear at one leather joint - $180

http://i160.photobucket.com/albums/t177/Shano3000/P1040146.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040148.jpg

22. Dashpad with airbag set-up - $250

http://i160.photobucket.com/albums/t177/Shano3000/P1040180.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040181.jpg

23. Middle dash gauges - $150

http://i160.photobucket.com/albums/t177/Shano3000/P1040165.jpg

24. Climate control - $120

http://i160.photobucket.com/albums/t177/Shano3000/P1040167.jpg

25. Seats. Have some minor staining which could be removed with a clean. Material has no rips or tears - $180set or $80 for each front seat and $40 for rear seats individually

http://i160.photobucket.com/albums/t177/Shano3000/P1040219.jpg

26. Factory nissan floor mats. Minimal signs of wear - $100

http://i160.photobucket.com/albums/t177/Shano3000/P1040152.jpg

27. Front door cards and back trim set - $150

http://i160.photobucket.com/albums/t177/Shano3000/P1040210.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040209.jpg

28. Boot trim. Complete set, one piece has 2 small tears which are unnoticeable once fitted. Comes with about 60% of plastic screws - $150

http://i160.photobucket.com/albums/t177/Shano3000/P1040173.jpg

29. Rear spoiler. Has a scrape along drivers side edge - $50

30. Front hub assembly - $100

http://i160.photobucket.com/albums/t177/Shano3000/P1040190.jpg

40. ABS Pump - $50

http://i160.photobucket.com/albums/t177/Shano3000/P1040178.jpg

41. Lower control arms, LCA's - $50 each

http://i160.photobucket.com/albums/t177/Shano3000/P1040188.jpg

42. Castor rods - $40 each

http://i160.photobucket.com/albums/t177/Shano3000/P1040189.jpg

43. Jack and tool kit - $40

http://i160.photobucket.com/albums/t177/Shano3000/P1040207.jpg

44. Complete seatbelt set - $150

http://i160.photobucket.com/albums/t177/Shano3000/P1040218.jpg

45. Under engine cover - $40

http://i160.photobucket.com/albums/t177/Shano3000/P1040203.jpg

46. Brake master with booster - $80

http://i160.photobucket.com/albums/t177/Shano3000/P1040216.jpg

47. Manual gearstick surround - $80

http://i160.photobucket.com/albums/t177/Shano3000/P1040179.jpg

48. Space saver rear tyre - $40

http://i160.photobucket.com/albums/t177/Shano3000/P1040194.jpg

49. Factory airbox with snorkel and panel filter - $200

http://i160.photobucket.com/albums/t177/Shano3000/P1040149.jpg

50. Middle air vent and hazard light switch - $40

http://i160.photobucket.com/albums/t177/Shano3000/P1040168.jpg

51. Passenger side Xenon headlight *DAMAGED* - $50

http://i160.photobucket.com/albums/t177/Shano3000/P1040193.jpg

http://i160.photobucket.com/albums/t177/Shano3000/P1040192.jpg

52. Badge set. Also includes "SKYLINE" from rear bar (Not pictured) - $30

http://i160.photobucket.com/albums/t177/Shano3000/P1040197.jpg

53. Dash cluster surround - $30

http://i160.photobucket.com/albums/t177/Shano3000/P1040196.jpg

54. Razo turbo timer - $30

http://i160.photobucket.com/albums/t177/Shano3000/P1040200.jpg

55. Rear parcel shelf - $30

http://i160.photobucket.com/albums/t177/Shano3000/P1040208.jpg

56. Drivers and passengers side front inner plastic wheel guards - $40 each

57. JVC DVD headunit. Model KW-AVX710. Fits perfectly into the dash of an R34 - $150

http://i160.photobucket.com/albums/t177/Shano3000/P1040170.jpg

Please contact me through PM here on SAU.

Edited by Shano3000

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...