Jump to content
SAU Community

Recommended Posts

so last week my window just stopped working, thang kod it stopped working while it was already up

the passenger side still works from the drivers side panel, when i press both buttons down it doesn't click like it used to

i'm just trying to work out if it is the motor or the panel

since i've had the car sometimes the windows will randomly stop working for a few seconds from the drivers side panel then start working again

i'm leaning towards electrical panel fault but has anyone else had the same problem?

Sounds like the motor if the switch panel is still working for the passenger side. The likes of half the switch panel just mysteriously "dying" out is very little. I've got a spare switch or regulator if you need.

Test the motor. Pull the door car off, find the two wires that are connected to the motor, next either locate the 12v and gnd wires and bridge the wires. Or if your not sure which ones are 12v pull the battery out and take it to the door use wires to link the motor to the battery. Just change the terinals to reverse the direction. If the motor goes up and down then ur relay box is munted.

yeah it sort of feels like it's the relay, it used to click when the windows were both down and you'd press the buttons both down

i'll pull the door card off today and have a look with a multimeter

I've got a spare switch or regulator if you need.

i will keep that in mind, do you also have the window motor available too? (depending on which one it is)

how much do you want for both parts individually?

Edited by mystery_kid

ok i just realised i have no idea where the window motor is in the door...

took some pics if anyone could help point out where i should be looking

http://i.imgur.com/iqA9zLt.jpg

http://i.imgur.com/EuBrzw4.jpg

http://i.imgur.com/3BsL0R9.jpg

http://i.imgur.com/gePrYR7.jpg

Edited by mystery_kid

Mate your looking for this:

http://www.google.com.au/search?q=r34+window+motor&hl=en&client=safari&source=lnms&tbm=isch&sa=X&ei=CZQpUeCYC-eYiAeL1IGAAw&ved=0CAgQ_AUoAQ&biw=320&bih=356#i=1

It will be bolted to the inner door skin(what the door card clips to.) should be located near the centre Of the door.

this happened to me last week,

Took the door skin off, held the switch in the up position (Window was stuck down)

And gave the motor a light tap with a hammer while still holding the switch..

Im guessing my motor must have been jammed because its had no problem since

Mate your looking for this:

http://www.google.com.au/search?q=r34+window+motor&hl=en&client=safari&source=lnms&tbm=isch&sa=X&ei=CZQpUeCYC-eYiAeL1IGAAw&ved=0CAgQ_AUoAQ&biw=320&bih=356#i=1

It will be bolted to the inner door skin(what the door card clips to.) should be located near the centre Of the door.

yep pretty much straight after posting those photos i googled it and worked out where it was

i'm not convinced it is the motor, i put my multi meter on the 2 signal wires and pressed down and it only came showed 6.5volts which isn't right, should be 12v or -12v depending on direction

yep pretty much straight after posting those photos i googled it and worked out where it was

i'm not convinced it is the motor, i put my multi meter on the 2 signal wires and pressed down and it only came showed 6.5volts which isn't right, should be 12v or -12v depending on direction

Yeh usually the motors last a lifetime, its the switches or amps that blow first. if you know anyone with the same r34 type as you (coupe/sedan) borrow their switch to see if it works.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • We have a huge update coming in the next few months, version 5 of Invision will be released. I'm holding off any changes until after this change as I'm not sure what features will be removed or introduced.
    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
×
×
  • Create New...