Jump to content
SAU Community

Recommended Posts

Rb26dett block no cracks etc 250

Rb26 complete head painted blue covers ready to bolt onto block $1000 or complete with plenum and turbo side $1450

Rb26 intake plenum painted blue, throttle bodies and adapter plate $280

Rb26 crank short snout $200

Rb26 sump with diff $150

R33 Gtr turbos complete with everything great condition $200

Rb26 flywheel $40

Rb26 balancer $30 small chip but is still fine

Rb26 engine brackets 20

Rb26 acc valve 50

Rb26 idle reg 50

Rb26 rods 50

Rb26 pistons 50

Many more engine parts available

Gold Coast

0487924497

Posted 15 February 2013 - 12:29 PM

Link to comment
https://www.sau.com.au/forums/topic/421829-rb26-parts-stripping-full-motor/
Share on other sites

65 posted for the AAC valve

As for the mounts I've only got the steel brackets not the rubber mounts

And they will be 35 posted

And the knock sensor loom I've got a r33 Gtr one ill have to check for you when I get home

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...